4. A 50 Hz, alternating voltage of 150 V (rms) is applied independently to (a) Resistance of 10 n, (b) Inductance of 0.2 H, (c) Capacitance of 50 pF . Find the expression for the instantaneous current in each case. Draw the phasor diagram in each case.

4. A 50 Hz, alternating voltage of 150 V (rms) is applied independently to (a) Resistance of 10 n, (b) Inductance of 0.2 H, (c) Capacitance of 50 pF . Find the expression for the instantaneous current in each case. Draw the phasor diagram in each case.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Related questions

Q: 1. A 70-Vac source has the following waveform. Determine: a. Vpk b. Vpk-pk C. Vrms d. Period e.…

A: Given a 70V AC source waveform (Vrms = 70V) Asked for the following Vpk Vpk-pk Vrms Period…

Q: A voltage is given by v(t)=50 sin(500πt+120°).. First, use a cosine function to express v(t). Then,…

Q: A 50 Hz, alternating voltage of 150 V (rms) is applied independently to (a) Resistance of 10 2, (b)…

A: In this question, find the instantaneous current with different different impedance. Draw the…

Q: A. There is a sinusoidal current i(t) that has an rms value of 20 A, a period of 1 ms, and reaches a…

A: Both parts have been attached in the following steps. the current equation for part a, voltage and…

Q: R1 L1 ww 50Q 10mH V1 C1 220 Vrms 10uF 60 Hz 0° Computed Values Compute the expected power factor of…

Q: For the circuit shown, what is the complex power, S, consumed by the load impedance? (Assume the…

A: The complex power is given by: S=VI*where,I* is conjugate of current I. Given: Vs=150∠0°R=15ΩC=150…

Q: . What effect does changing the frequency on the effective value of sinusoidal voltage? 2. What…

A: Consider a sinusoidal voltage voltage shown below, Here v=Vmsinωt The peak voltage is Vm and ωt=α…

Q: What is the equation of the current in B in the function of sin given that Two electric devices A…

Q: 1. How much value of capacitance should you place to correct the power factor of a load consisting…

Q: When the average real power absorbed by an impedance is zero, then the impedance is: Select one: O…

A: The real power is absorbed by the resistor only when there is a combination of inductor and…

Q: The rms value of a 60HZ single phase ac voltage source is 100V and its internal resistance is 0.1 Q.…

A: In the question, A voltage sources V= 100V & 60Hz is supplied to resistance R= 1ohm Inductance…

Q: A 10.8-2 resistor, a 11.8-uF capacitor, and a 16.4-mH inductor are connected in series with a 130-V…

A: current is maximum at resonant frequency. For series RLC resonant frequency=12πLC current at…

Q: Calculate the current drawn from the source with and without the capacitor connected. Determine the…

Q: Two current sources deliver current to a common load. The first source delivers a current whose…

Q: The rms value of a 60HZ single phase ac voltage source is 100V and its internal resistance is 0.1 Q.…

A: b)xL=wL=2π×60×10-3 =0.3769ΩZ=0.1+1+j0.3769 =1.1+1+j0.3769…

Q: The phasor voltage Vab in the circuit shown is 24020 ° V (rms) when no external load is connected to…

A: Given Vab=240∠0° VZ=80-j60 Ω (a) When the no-external load is connected When no external load is…

Q: Now write the time domain function, assuming 60 Hz operation for the following rms phasors; repeat…

Q: The sinusoidal voltage source in the circuit below operates at a frequency of 50 Hz. Match a value…

A: In the given question we have only resistors in the registers we don't have any significance of…

Q: V1 C1 220 Vrms 10uF 60 Hz 0° Computed Values Compute the expected power factor of the circuit given…

Q: A load connected to a 120 Vrm source is drawing 1,600 VA at 0.6 power factor lag. a) What is the…

Q: Household appliances - refrigerator, lamp, and microwave are connected to the voltage sources as…

Q: Circuit Diagram V1 R1 220 Vrms >5002 60 Hz 0.⁰ L1 100mH Computed Values Compute the expected power…

A: Note:- As connection of capacitor is not given whether it is series or parallel. I solved it by…

Q: An electromagnet is modeled as L=0.3H and R=200 in series, and connected to a 120V(rms) sinusoidal…

A: Solve the above questions

Q: 1. A 70-Vac source has the following waveform. Determine: a) Vp b) Vpk-pk c) Vrms d) Period e)…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: The rms value of a single-phase ac voltage source is V. The voltage source will power two loads in…

A: a)Z,is associated with Resistor (R1) and inductor(L),both are in series Reactance of L, jxL=j 2πf…

Q: 1 H 7. The circuit shown in the figure has two sources connected in series. Find the rms 10 value of…

Q: A 50 Hz, alternating voltage of 150 V (rms) is applied independently to: (d) resistance of 10 ohms,…

A: Supply voltage = 150 vrms F = 50 hz so the supply voltage we can take (V) = 1502sin(ωt)…

Q: Circuit Diagram V1 C1 220 Vrms 10uF 60 Hz 0° Computed Values Compute the expected power factor of…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: voltage is +80 V k. the time (2nd occurrence) after t = 0 when the voltage is –10 V Answers: a.…

Q: The circuit shown in Figure Q5.1 consists of a current source connected to a load via a cable. The…

A: Given circuit is - Value of current source is -

Q: five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let…

A: First, convert the parameter of the passive elements connected in the circuit in the same unit in…

Q: 10. Add the voltages below together. v:(t) = 150 0 rad/st) v sin(10 v2(t) = 100 sin (100 rad/st +5)…

Q: A voltage is given by v( t )=10 sin(1000πt+30°). First, use a cosine function to express v(t). Then,…

A: Given data: vt=10sin1000πt+30° vt=10sin1000πt+30°cos90°-z=sin…

Q: Find the RMS value of the waveform depicted below. Given A = 9, a = 2, b = 8, and T = 13 %D

Q: A 50 Hz, alternating voltage of 150 V (rms) is applied independently to (a) Resistance of 10 Ω, (b)…

A: Given: Alternating voltage f=50 HzVrms=150 V

Q: A 50 kW load operates from a 60 Hz, 10 kV rms line with a power factor of 0.6 lagging. Determine the…

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: 3. Write the sinusoidal expressions for voltages and currents having the following rms values at a…

A: Dear,as per company guidelines we can answer only one question at a time, kindly post other question…

Q: Circuit Diagram R1 L1 50Q 10mH V1 220 Vrms C1 10uF ~60 Hz 0° Computed Values Compute the expected…

A: Capacitor: This is an energy storage device that store the energy in the form of the electric field.…

Q: For a source which has: • Vrms = 345 V • P= 8195 W • pf = 0.95 What is the rms current?

A: In this question we need to find RMS current .

Q: Assuming that a nonzero ac voltage source is applied, what can you say about whether the power and…

A: The series LC circuit is given below,

Q: When connected to 230 V (rms) ,50 Hz power line, a load absorbs 4 kW at a lagging power factor of…

Q: A sinusoidal voltage is given by the expression vs = 340 cos(100nt + 20°). By analyzing the given…

A: In this question voltage wave is given....We have to find out current equation , phase angle and…

Q: Circuit Diagram V1 R1 220 Vrms >50 Ω 60 Hz 0.⁰ L1 100mH Computed Values Compute the expected power…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: L1 R1 mm 50Q 10mH V1 C1 220 Vrms :10uF 60 Hz 0° Computed Values Compute the expected power factor of…

Q: Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 600 Hz. R=2…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: An AC source Vs1(t) and a DC source V2 is applied together to the circuit given below. a Find and…

A: L = 0.01H C= 0.0001F R1= R2= 10 ohm Vs(t) = 10√2 cos1000t v Vs = 10 v

Q: Prob I and Vc For the following RMS phasor circuit, a coworker has determined values for 50 Ohms 50…

A: In this question, Find the value of current in the resistance R2 and active and reactive power in…

Concept explainers

Code Conversion

The method or technique used to convert code from one format to another is termed code conversion. Code conversions are most commonly used in computers, digital electronics, microprocessors, etc.

Question

Draw the circuit diagram of the problem and round off answers to 4 decimal places.

4. A 50 Hz, alternating voltage of 150 V (rms) is applied independently to (a)
Resistance of 10 n, (b) Inductance of 0.2 H, (c) Capacitance of 50 µF .
Find the expression for the instantaneous current in each case. Draw the phasor
diagram in each case.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Arithmetic Operation and Code Conversion in Number System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two sinusoidal voltages of the same frequency have rms values of 8 V and 3 V. What is the smallest rms value that the sum of these voltages could have? The largest? Justify your answers.
A voltage is given by v( t )=10 sin(1000πt+30°). First, use a cosine function to express v(t). Then, find the angular frequency, the frequency in hertz, the phase angle, the period, and the rms value. Find the power that this voltage delivers to a 50-Ω resistance. Find the first value of time after t=0 that v(t) reaches its peak value. Sketch v(t) to scale versus time. * Denotes that answers are contained in the Student Solutions files. See See Appendix E for more information about accessing the Student Solutions.
A voltage is given by v(t)=50 sin(500πt+120°).. First, use a cosine function to express v(t). Then, find the angular frequency, the frequency in hertz, the phase angle, the period, and the rms value. Find the power that this voltage delivers to a 50-Ω resistance. Find the first value of time after t=0 that v(t) reaches its peak value. Sketch v(t) to scale versus time. * Denotes that answers are contained in the Student Solutions files. See See Appendix E for more information about accessing the Student Solutions.
Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags A by p/3 radians and the line current is 23.3 amp, determine the current in B.
A 50 Hz, alternating voltage of 150 V (rms) is applied independently to (a) Resistance of 10 Ω, (b) Inductance of 0.2 H, (c) Capacitance of 50 μF. Find the expression for the instantaneous current in each case. Draw the phasor diagram in each case.
Consider a 760 W light bulb that requires an RMS voltage 21 V to operate normally. How large should an inductance be connected in series with the bulb if the combination is connected across a RMS voltage 255 V, 71 Hz line? (You may neglect the resistance of the inductor and the inductance of the light bulb.)
What is the equation of the current in B in the function of sin given that Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by π/3 radians and the total linecurrent is 23.4 amp. (rms).
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). a) Suppose that between the two terminals of an element there is a voltage v (t) and that a current i (t) enters through the terminal marked with a positive sign. Show that if v (t) and i (t) are sinusoidal and are out of phase by an angle ϕ, then the active power P that is consumed by said element is proportional to cos ϕ. b) How much is P for a pure inductor and how much for a pure capacitor? Does this make physical sense? c) When specifying the power factor seen between two terminals, why is it necessary to indicate whether it is lagging or leading? d) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. Then repeat the procedure but for two elements in series. e) What meaning would you give to the P consumed…
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). a) Suppose that between the two terminals of an element there is a voltage v (t) and that a current i (t) enters through the terminal marked with a positive sign. Show that if v (t) and i (t) are sinusoidal and are out of phase by an angle ϕ, then the active power P that is consumed by said element is proportional to cos ϕ b) How much is P for a pure inductor and how much for a pure capacitor? Does this make physical sense? c) When specifying the power factor seen between two terminals, why is it necessary to indicate whether it is lagging or leading?
An industrial process requires a power of 10 kW with a lagging power factor of 0.6 in a single-phase system. It is desired to add a parallel capacitance to raise the power factor to unity. For a line voltage of 240 V rms, determine the value of capacitance required.
A. There is a sinusoidal current i(t) that has an rms value of 20 A, a period of 1 ms, and reaches a positive peak at t = .3 ms, write an expression for i(t). B. The voltage v(t) = 10 sin(250π(t)) V appears across a 20 ohm resistance. Sketch v(t) and p(t) to scale versus time. Find the average power delivered to the resistance.
Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by pi/3 radians and the line current is 23.4 amp, determine the current in B.