4. A Parallel RLC having a resistance of 100 ohms, an inductance of 0.53 henry, with a capacitance of 8.84 micro farad is connected to a 220 volts, 60 cps source. Calculate the following. a) the total impedance, b) Currents of these 3 branches, c) total power d) power Factor e) KVA f) RKVA

4. A Parallel RLC having a resistance of 100 ohms, an inductance of 0.53 henry, with a capacitance of 8.84 micro farad is connected to a 220 volts, 60 cps source. Calculate the following. a) the total impedance, b) Currents of these 3 branches, c) total power d) power Factor e) KVA f) RKVA

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter3: Magnetic Starters

Section: Chapter Questions

Problem 30SQ

See similar textbooks

Related questions

Q: Find the average value of a half-wave rectified signal with a peak value of 20 mV.

A: Given data For half wave rectifier: Peak value Vp = 20 mV Average value Vavg = ? Formula Vavg = ...

Q: 2A Find the diuretic consumed in Is resistance 12 L SA 132 Q 12 by finding the lems of the three cur...

Q: An LTI system with impulse response h(n) = 3u(n- 1) is: O a Memoryless. O b. Stable. O c. Non of the...

A: The solution is given below

Q: 2. Use mesh analysis to find v. 5 V 15 V 2.

A: Given,

Q: 3) (a) Complete the truth table (Table 2) for the logic circuit of Fig 3 (b) Hence, derive the simpl...

Q: A resistor of R = 10 ohms and an inductor of L = 0.005h are in parallel. The current in the inductiv...

Q: The humper Bridge in England has the world's longest single span, 1410 m. Calculate the change in le...

Q: write node-voltage equations: one for each input terminal of the op amp. R4 R3 Vo O41 R2 R1 + RL Vin...

Q: Problem 4 A single-phase, 10KVA, 2200/220V transformer has the following parameters: R1=4.0 N, R2=0....

A: GIVEN: KVA rating=10kVAV1V2=2200220VR1=4.0ΩR2=0.04ΩX1=5.0ΩX2=0.05ΩRc1=35kΩXm1=4.0kΩlagg...

Q: The second question: a wheel rotates from rest with uniform angular acceleration, and its speed reac...

Q: Y(s) 2) Let kr6 and a-2. Find the range of k for the stability of the closed-loop system. R(s) as-b

Q: 950 ohms RL 10kO SAKey-A V1 25V D1 12% Vz= 15V When the varistor is set to 12, compute the following...

Q: a. What is the peak value of the waveform? b. What is the peak to peak value of the waveform? c. Wha...

A: One division in x axis is equal to 1 m sec and one subdivision is 0.2msec One division in y ax...

Q: Give the coefficients A, B, C, and D

A: Split the x(s) into a form for which we can use direct inverse laplace transform . Then compare with...

Q: 1. A metallic conductor has a resistivity of 18 x 100m. What is the resistance of a piece that is 30...

Q: Q12: A certain sinusoid at a frequency of fm Hz is used at the modulating signal in both an AM (DSB ...

Q: A cable has a VSWR of 10. If the minimum voltage along the cable is 20 volts, what is the maximum vo...

Q: What is the current in a circuit with a2Ωresistor followed by a3Ωresistor that are both in parallel ...

Q: ix 10 2 8 A VB 82 10 VA Vc ↑ )1 A Figure 1 cuit shown, write out the equations needed to solve for t...

Q: 1. Why do we apply reduction factors in the design of electric equipment? Also, why do we increase t...

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any s...

Q: T or F, modify the wrong part if False, please underline twice your answer if True or False. Lap-w...

Q: Develop the relevant schematic diagram in order to build the Astable Multivibrator using 555 Timer c...

A: It is asked to develop the schematic diagram for Astable Multivibrator by using 555 timer circuit. A...

Q: Ic(mA) 110 µA 100 μΑ 90 µA- 10 -80 μΑ. 70 μΑ 8 60 μ. 50 μΑ 40 μΑ. 30 μ. 3 20 μΑ 10 µA 10 15 20 25 30...

Q: T or F, modify the wrong part if False, please underline twice your answer if True or False. At ...

A: FALSE The given statement is false Efficiency is defined as the ratio of output to input output = i...

Q: Electrical Engineering 12 0.1 f 1Ω 1Ω Vin 1f Vo 2. Frequency scale your circuit by wo = 2x104 a. Dra...

Q: Ex (5):-. A compact disc (CD) records audio signal digitally by using PCM. Assume the audio signal b...

A: We need to find number bits per sample and we need to find out data rates .

Q: • T or F, modify the wrong part if False, please underline twice your answer if True or False. S...

A: FALSE The given statement is FALSE for the given synchronous motor or generator synchronous motors a...

Q: さ、。メメ 2 toy ら一9 decoder 9. -

Q: a. From the figure , write note voltage equations, one for each input terminal of the op amp b. The ...

A: Use virtual ground concept.

Q: Consider an uncertain system i(t) = x(t) + u(t), where the c;'s are constants with unknown C2 values...

Q: 1. Use nodal analysis to determine Vo in the following circuit. (20 points) 3 V +) 9 V 3Vo 6Ω ALE

Q: Take a look at Figure 3. Please find the current through the segment of the bottom wire between the ...

A: Given circuit,

Q: Input Count 1 1 2 3

Q: ww Problem 5. Determine the value of Vo 42 ww ww 32 3k2 ASI USS°A

A: The solution is given below

Q: 1Ic(mA) 110 µA 100 μΑ. 90 µA- 10 : 80 μΑ 70 μΑ 60 µA 50 μΑ. 140 μΑ. 5 30 µA 4 -20 μΑ 2 10 µA Ig = 0 ...

A: BJT: This is used as a transistor and has three terminals base, emitter, and collector terminals.

Q: III. Solve: 9i ánd B =6 -31 a) Magnitude and Angle of A and B b) A(A+B) c) (A+B)/(A-B)

Q: 25 V t = 0 4 H Turn on the circuit and findt = 1,t = 2, t = 3, t = 4, t = 5

A: After turn on the switch , inductor and 2 ohm resistor become short.

Q: 3. For a parallel circuit of 20 ohms resistor and a 10 ohms inductor, is connected to a 110/60 cps V...

A: We need to find out current for given circuit

Q: 7. Determine the base voltage VB in the circuit. If RE is doubled, what will be the value of VB? +15...

A: As per our company guidelines we are supposed to answer only first question kindly repost other ques...

Q: 20x ix 10 Ω 8 A 82 VB 1Ω VA Vc 1 A 5Ω 2Ω. 1) +

A: Here Va and Vc nodes forms super node because present of dependent voltage source between those two ...

Q: or the circuit shown in Fig. 1 below, the transistor parameters are B =150, VBE =0.7V and VT=26mV. a...

Q: Theoretical calculations: 1. Draw the spectrum of AM-SSB ? 2. What is the minimum band width require...

A: We are authorized to answer three sub-parts at a time, since you have not mentioned which part you a...

Q: 1. For the circuit below: a. Write the node voltage equations for V1 and V2. b. Assume the 15mF capa...

A: In this question, Two independent energy sources are consist in the circuit. Find the node voltage...

Q: 2s laplace transform F(s) : %D (s² + 2) F(s) = %3D (s2 – 2) (s2 + 2) 3.

Q: Si 2.2 k 2.2 km 10 mA +20 V o-20 V 6.8 ka Si (b) FIG. 2.158

A: We need to find current and voltage for given circuit

Q: how the bleeding resistor and zener diode regulate the DC voltage across the filter capacitor of the...

A: Zener diode- A specialized diode which allows the passing of current in both conditions as forward ...

Q: Define the following terms for FSK modulation: frequency deviation, modulation index, and deviation ...

Q: An aluminum wire 5m long and 2mm diameter is connected in parallel with a copper wire 3m long. The t...

A: Since the wire is connected in parallel, the total current in the wire is given as: It=ICu+IAlIt=4 ...

Q: Cireuit 4. Draw and la bel the Diagram. a) Half-Wowe Rec tification. b) Fullwave Rec ti fication (Br...

Q: Find the general solution of the equation: y" - y' - 6y = exp(-x) - 7 cos x

A: calculation of general solution of given differential equation : y''-y'-6y=e-x-7cosx We know, Genera...

Question

4. A Parallel RLC having a resistance of 100
ohms, an inductance of 0.53 henry, with a
capacitance of 8.84 micro farad is connected
to a 220 volts, 60 cps source. Calculate the
following. a) the total impedance, b) Currents
of these 3 branches, c) total power d) power
Factor e) KVA f) RKVA

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In an R-L parallel circuit, ET=240 volts, R=560, and XL=330. Find apparent power.
A series circuit composed of a resistance of 24 ohms, an inductance of 0.09 henry and a capacitance of 8 microfarad, is connected to a 120-volt 50-Hz supply. Calculate the (a) power factor of the circuit, (b) total reactive power, (c) voltage drop accross the inductor.
A circuit is composed of a resistance of 22 ohms, an inductance of 0.11 henry and a capacitance of 12 microfarad, all connected in parallel to a 115-volt 60-Hz supply. Calculate the (a) total current, (b) total reactive power, (c) and the power factor of the cicruit.
8. A parallel circuit of 25 – ohm resistor, 64 – mH inductor and 80 - μF capacitor connected across a 110 V, 50 Hz, single phase supply is shown in the figure below. Calculate the current in the individual element, the total current drawn from the supply and overall power factor of the circuit. Draw a neat phasor diagram showing IR, IL and IC.
4.a. A demountable stud bushing on high-voltage leads eliminates the need fora. an oil stop.b. a gasket.c. a terminal lug. 4.a. A power transformer with standard insulation class of 69 kv will withstand an rms test voltage ofA. 140 kv.B. 440 kv.c. 69kv.
A series circuit consists of resistance of 10 ohm, an inductance of 200/π mH and capacitance of 1000/π μF . Calculate (a) the current flowing in the circuit if supply voltage is 200 V, 50 Hz, (b) power factor of the circuit, (c) power drawn from the supply. Also draw the phasor diagram.
A parallel circuitcomprisestwo branches, (i) a coil of resistance 20 Ω and inductance 0.07 H and (ii) a capacitance of 60 μF in series with a resistance of 50 Ω. Calculate the current in the mains, active-, reactive-powers,and the power factor of the arrangement when connected across a 200V, 50Hz supply.
a 10 kiloohms resistor is connected in parallel with an inductor L. The parallel combination is then connected in series with a 2 kiloohms resistor and 5nF capacitor. If the whole combination is connected to a voltage supply of 50cis0 volts at a frequency of w=50,000rad/s, find the value of L such that the total current is in phase with the supply voltage. ("in phase") means that the voltage and the current have the same angular displacement.
A machine shop is fed by a 250 kVA 480 V three-phase electrical service. On one of thebranches leading away from the service, the shop runs several manufacturing machines,giving the branch a load profile of 175 kW with a 0.85 lagging PF.Determine the minimum allowed gauge of the branch conductors. Branch conductors arealuminum, THW, contained within a raceway with an ambient temperature of 40 ºC
A resistance of 1.5kΩ, an inductance of 2.5H, and a capacitor of 6 micro Farads, each are connected in parallel with a 220-V generator, with frequency 60 Hz. a) What is the phasor relationship between the current and the voltage in the circuit? b) Calculate the real(P) power c) Calculate the reactive(Q) power d) Calculate the apparent(S) power
12. A series circuit having pure resistance of 40 ohms, pure inductance of 50.07 mH and acapacitor is connected across a 400 V, 50 Hz, AC supply. This R, L, C combination drawsa current of 10 A. Calculate (a) Power factor of the circuit and (b) Capacitor value.
A coil with an inductance of 100 mH is connected in series with a resistance of 20 Ω. To this system If 110 V AC with a frequency of 25 Hz is applied, the impedance, current, resistance and coil of the system Find the voltage at the terminals, active, reactive and apparent power values of the system.