4. A smoking lounge is to accommodate 15 heavy smokers. The minimum fresh air requirement for smoking lounges is specified to be 30 L/s per person (ASHRAE, Standard 62, 1989). Determine the minimum required flow rate (kg/s) of fresh air that needs to be supplied to the lounge, and the diameter of the duct if the air velocity is not to exceed 8 m/s. Use density of air = 1.20kg/m. Smoking kounge Fan 15 smokers

4. A smoking lounge is to accommodate 15 heavy smokers. The minimum fresh air requirement for smoking lounges is specified to be 30 L/s per person (ASHRAE, Standard 62, 1989). Determine the minimum required flow rate (kg/s) of fresh air that needs to be supplied to the lounge, and the diameter of the duct if the air velocity is not to exceed 8 m/s. Use density of air = 1.20kg/m. Smoking kounge Fan 15 smokers

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Engineer CoolAir is working on designing an air conditioning unit that handles the combined air flow from two food processing rooms with the following quantities: 4000 ft^3/ min at 80° F wet bulb and 50% saturated; 3000 ft^3/min at 70° F dry bulb and 65°F wet bulb temperatures. (a) What is the total mass flow rate? (b) What is the dry bulb temperature? (c) what is the wet bulb temperature?
In climates with low night-time temperatures, an energy-efficient way of cooling a house is to install a fan in the ceiling that draws air from the interior of the house and discharges it to a ventilated attic space. Consider a house whose interior air volume is 720 m3 If air in the house is to be exchanged once every 20 minutes, determine (a) the required flow rate of the fan and (b) the average discharge speed of air if the fan diameter is 0.5 m..
Air at a static temperature and pressure of 8°C and 75 kPa respectively enters the intake of an aircraft gas turbine engine with a velocity of 196 m/s. The intake may be regarded as a diffuser with an inlet area of 0.4 m2 and an exit area that reduces the air flow velocity essentially to zero. Calculate the mass flow rate (kg/s) of air through the intake, given the specific gas (air) constant as 287 J/(kg.K), keeping three decimal places.
The maximum velocity of an air flow (v= 700 ms-1 and T=160 oC
A fan is to be selected to ventilate a bathroom whose dimensions are 2 m × 3 m × 3 m. The air velocity is not to exceed 7 m/s to minimize vibration and noise. The combined efficiency of the fan–motor unit to be used can be taken to be 50 percent. If the fan is to replace the entire volume of air in 15 min, determine (a) the wattage of the fan–motor unit to be purchased, (b) the diameter of the fan casing, and (c) the pressure difference across the fan. Take the air density to be 1.25 kg/m3 and disregard the effect of the kinetic energy correction factors.
Air at a static temperature and pressure of 9°C and 100 kPa respectively enters the intake of an aircraft gas turbine engine with a velocity of 206 m/s. The intake may be regarded as a diffuser with an inlet area of 0.4 m2 and an exit area that reduces the air flow velocity essentially to zero. Calculate the mass flow rate (kg/s) of air through the intake, given the specific gas (air) constant as 287 J/(kg.K)
Select the flow work (energy) of a flowing fluid below, where is velocity and is total volume. __________ A. B. C. D.
Question No. 1a) A rigid tank containing 0.4m3 of air at 400 kPa and 30oC is connected by a valve to a piston cylinder device with zero clearance. The mass of the piston is such that a pressure of 200 kPa is required to raise the piston. The valve is opened slightly and air is allowed to flow into the cylinder until the pressure of the tank drops to 200 kPa. During this process, heat is exchanged with the surrounding such that the entire air remains at 30oC at all times. Determine the heat transfer for this process.
Liquid benzene at 38 C with a vapor pressure of 26.4 kN/m2 and a density of 860 kg/m3 isto be pumped at a rate of 0.0025 m3/s from a storage tank to a discharge location 3 m abovethe liquid level in the tank. The pump with a mechanical efficiency of 60 percent is 1 mabove the liquid level. The storage tank is at atmospheric pressure. The pressure at the endof the discharge line is 445 kPa absolute. The inside diameter of the pipe used to transfer thebenzene is 0.0409 m. The frictional pressure drops in the suction line and the discharge linehas been evaluated as 3.45 and 37.9 kN/m2, respectively. Determine the head developed bythe pump and the total power requirement. If the pump manufacturer specifies a required netpositive head of 3.0 m, will such a pump be applicable for this service?
Air flows into a turbine at a rate 30 [m 3 /s], a temperature of 1100 [K] anda pressure of 300 [kPa]. The turbine’s work output is 200 [kJ/kg]. Determine thetemperature of the air at the exit, the power output in [kW] and the isentropicefficiency. The pressure ratio of the turbine is 3. The specific gas constant, R, for airis 0.287 [kJ/kg-K].
Air whose density is 0.082 lbm/ft3 enters the duct of an air-conditioning system at a volume flow rate of 450 ft3/min. If the diameter of the duct is 16 in, determine the velocity of the air at the duct inlet and the mass flow rate of air.
The approach and efficiency of cooling tower are 10 oC and 65 %, respectively. If the temperature of water leaving the tower is 27 oC, determine the temperature of water entering the tower.