convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of fluid at the inlet are 3,160 kJ/kg and 241 km/hr respectively. At the exit the specific enthalpy of fluid is 2,693 J/kg. Calculate the velocity of the fluid at the exit of the nozzle in m/s,

convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of fluid at the inlet are 3,160 kJ/kg and 241 km/hr respectively. At the exit the specific enthalpy of fluid is 2,693 J/kg. Calculate the velocity of the fluid at the exit of the nozzle in m/s,

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.37P

See similar textbooks

Similar questions

The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of fluid at the inlet are 3,351 kJ/kg and 298 km/hr respectively. At the exit the specific enthalpy of fluid is 2,619 J/kg. Calculate the exit area (in mm2)of the nozzle when the specific volume at the nozzle exit is 0.61 m3/kg at the inlet area of 0.23 m2 and the specific volume at the inlet is 0.33 m3/kg. You do not need to include the unit for this question.
An end-burning rocket motor has a chamber diameter of 10 cm and a nozzle exit diameter of 8 cm. The density of the propellant is 1750 kg/m3 and the surface regresses at the rate of 1 cm/s. The gases crossing the nozzle exit plane have a pressure of 10 kPa abs and a temperature of 2200°C. The gas constant of the exhaust gases is 415 J/kg.K. Calculate the gas velocity at the nozzle exit plane in m/s.
The liquid storage tank shown in Fig has two inlet streams with mass flow rates w1 and w2 and an exit stream withflow rate w3. The cylindrical tank is 2.5 m tall and 2 m in diam-eter. The liquid has a density of 800 kg/m. Normal operating procedure is to fill the tank until the liquid level reaches a nom-inal value of 1.75 m using constant flow rates:w1=120 kg/min, w2=100 kg/min, and w3=200 kg/min. At that point, inlet low rate w1 is adjusted so that the level remains constant.However, on this particular day, corrosion of the tank has opened up a hole in the wall at a height of 1 m, producing a leak whose volumetric flow rate q4(m3/min) can be approximated by q4=0.025√h−1 where h is height in meters.(a)If the tank was initially empty, how long did it take for theliquid level to reach the corrosion point?(b)If mass flow rates w1,w2,and w3 are kept constant indefi-nitely, will the tank eventually overflow? Justify your answer.
Determine the mass flow rate (kg/s) of water that must flow through a conduit to carry 15,000 kJ/s of heat energy if the temperature difference is 10 degrees Celsius. Cp water=4.186 k*J/Kg*K
Oil with ? = 876 kg/m3 and ? = 0.24 kg/m·s is flowing through a 1.5-cm-diameter pipe that discharges into the atmosphere at 88 kPa. The absolute pressure 15 m before the exit is measured to be 135 kPa. Determine the flow rate of oil through the pipe if the pipe is (a) horizontal, (b) inclined 8° upward from the horizontal, and (c) inclined 8° downward from the horizontal.
Air enters a 7-m-long section of a rectangular duct of cross section 15 cm X 20 cm at 50°C at an average velocity of 7 m/s. If the walls of the duct are maintained at 10°C, determine: (a) the outlet temperature of the air, (b) the rate of heat transfer from the air, and (c) the fan power needed to overcome the pressure losses in this section of the duct.
Five hundred kilograms per hour of steam moves a turbine. The steam enters the turbine at 44 atm and 450°C with a speed linear 60 m/s, and exits at a point 5 m below the inlet, at pressure atmospheric and at a speed of 360 m/s. The turbine provides work on the shaft with a rating of 70 kW, and the heat loss in the turbine is estimated at 104 kcal/h. Calculate the variation in specific enthalpy associated with the process.
The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6 m3/s air at atmospheric conditions of 20°C and 1 bar (100 kPa) and consumes 300 kW electric power when operating. Air is compressed to a gage pressure of 8 bar (absolute pressure of 900 kPa), and compressed air is transported to the production area through a 15-cm-internal-diameter, 83-m-long, plastic (smooth) pipes with a surface roughness of 0.15 mm. The average temperature of compressed air in the pipe is 60°C. The compressed air line has 8 elbows with a loss coefficient of 0.6 each. In order to reduce the head losses in the piping and thus the power wasted, someone suggests doubling the diameter of the 83-m-long compressed air pipes. Calculating the reduction in wasted power, and determine if this is a worthwhile idea. Considering the cost of replacement, does this proposal make sense to you?
The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6 m3/s air at atmospheric conditions of 20°C and 1 bar (100 kPa) and consumes 300 kW electric power when operating. Air is compressed to a gage pressure of 8 bar (absolute pressure of 900 kPa), and compressed air is transported to the production area through a 15-cm-internal-diameter, 83-m-long, galvanized steel pipe with a surface roughness of 0.15 mm. The average temperature of compressed air in the pipe is 60°C. The compressed air line has 8 elbows with a loss coefficient of 0.6 each. If the compressor efficiency is 85 percent, determine the pressure drop and the power wasted in the transportation line.
The thrust developed by the engine of a Boeing 777 is about 380 kN. Assuming choked flow in the nozzles, determine the mass flow rate of air through the nozzle. Take the ambient conditions to be 215 K and 35 kPa.
A U-tube open at both ends is partially filled with water. Oil having a density of 750 kg/m3 is then poured into the right arm and forms a column L = 10.00 cm high. The density of air is 1.29 kg/m3.The right arm is then shielded from any air motion while air is blown across the top of the left arm until the surfaces of the two liquids are at the same height. (d) Determine the pressure difference between the water and oil columns(e) Determine the speed of the air being blown across the left arm.
Wind blows steadily at 7 m/s into the blades of a wind turbine. Compute the actual electric power generation of the system assuming an overall efficiency of 30 percent of a wind turbine with 80-m-diameter blades. The air density is 1.25 kg/m3. Answer in KW.