Identify the energy carried by a fluid stream crossing a control surface as the sum of internal energy, flow work, kinetic energy, and potential energy of the fluid and to relate the combination of the internal energy and the flow work to the property enthalpy.

Identify the energy carried by a fluid stream crossing a control surface as the sum of internal energy, flow work, kinetic energy, and potential energy of the fluid and to relate the combination of the internal energy and the flow work to the property enthalpy.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.33P

See similar textbooks

Related questions

Q: Explain the the mechanical efficiency of a fan is the ratio of the rate of increase of the…

A: Kinetic energy is only mechanical energy of air . If we consider a fan to which we give some power…

Q: Oil is pumped from a very large tank (z1 = 150 m) to another tank (z2 = 200 m), located higher and…

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A: Given, Nozzle inlet: Nozzle outlet:

Q: (iv) Consider a steady flow mixing process. Under what conditions will the energy transported into…

A: Steady flow means the properties should remain constant with respect to time at a particular…

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A: h1=3089 KJkgc1= 229 kmhrc1= 229×518=63.61 msech2= 2569 Jkg v2= .63 m3kgA1=.2 m2v1=.31 m3kgNow apply…

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

Q: the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily…

Q: A laser Doppler velocimeter was used to determine the velocity of the water flow in an open channel…

Q: work on the principle that the flow through an orifice will be constant if the pressure drop remains…

A: Non pressure compensated valve is used where the system pressures are relatively constant and the…

Q: Constant operating speed characteristics; H = 55 – 460v² and ng = 8,2 – 130v³ Water is drawn from a…

Q: A duct 0.40 m high and 0.80 m wide suspended from the ceiling in a corridor, makes a right angle…

A: Given data as per the question The inner radius = 0.2 m outer radius = 1.0 m The velocity of air in…

Q: The fluid condition at the Inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A: Inlet velocity:- 289km/hr = 80.27 m/s Inlet area = 0.24 m² Specific volume…

Q: If the Darcy Weisbach friction factor for a fluid flow through a pipeline is calculated as0 016, the…

A: When a fluid flows from one section to another section, there occurs a reduction in its total energy…

Q: Water flows between two reservoirs A & B. The water level in A is 400 m AOD and in B is 385m AOD.…

Q: At a particular operating condition, an axial flow compressor has a reaction of 0.6, a flow…

A: Given: The reaction of the axial flow compressor is R = 0.6. The flow coefficient is φ = 0.5. The…

Q: PROBLEM 1 A hydroelectric power plant has the hydraulic turbine located 60 m below the elevation of…

Q: A pipe carrying water has an inlet of diameter 0.18 m and an outlet which is 1.11 m below the inlet…

Q: Rank in order, from highest to lowest, the liquid heights h1 to h4 in tubes 1 to 4. The airflow is…

A: The height of liquid in tube increases with the increase in velocity, since higher the velocity,…

Q: Gas is flowing through a square conduit whose section gradually changes from 150 mm (section 1) to…

A: Given:Side of square conduit at section 1, L1=150 mm=0.150 mSide of square conduit at section 2,…

Q: For flow of water at a Reynolds number of 1.03E6 through a 5-cm-diameter pipe of roughness height…

Q: Determine the static fan efficiency if total fan mechanical efficiency is 70% and air is measured at…

A: Given DataQ=1.42m3/sηm=70%d2=275mmhw=2.54cmd1=300m

Q: Determine the expected Fanning friction factor for water at 28 degrees Celsius, flowing through a…

A: Give data as per the question The internal diameter of the tube =15 mm = 0.015 m velocity =0.3 m/s…

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

Q: 12-58 Water enters a hydraulic turbine through a 30-cn diameter pipe at a rate of 0.6 m/s and exits…

Q: A liquid with a density of 0.8 [g/ml] flows through a tube with an inner diameter of 50 [mm]. There…

A: Given: Orifice coefficient, Co = 0.61 Orifice diameter, Do = 25.4 mm Diameter, D = 50 mm Find: Flow…

Q: A sudden enlargement in a circular duct measures 0.20 m diameter upstream and 0.40 m downstream. The…

A: Answer: The flow rate through the duct is 0.38 m3/sec.

Q: A differential thermocouple with sensors at the inlet and exit of a pump indicates that the…

A: Given data ∆T=0.048 °FV=1.5 ft3/sec

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

Q: Water is sent to a cylindrical tank with a height of 3 m and a diameter of 1 m through a pipe with a…

Q: Water enters a hydraulic turbine through a 40-cm diameter pipe at a rate of 0.6 m3/s and exits…

Q: Oil whose temperature is constant at 20 ° C (ρ = 886 kg / m3, μ = 0.805 kg / m / s) It flows…

A: GivenT=20°Cρ=886kg/m3μ=0.805kg/m/sPi=720KpaL=40mP0=101Kpa

Q: Water is drawn from a pond by means of a centrifugal pump given with equations, and it is pumped…

Q: The power carried by fluid into the control volume, (W). Head carried by fluid out the control…

A: Total energy available at entry per unit volume is given by the the bernoulli's equation P₁ +…

Q: Q.: In a test of water cooled air compressor, it is found that the shaft work required to drive the…

A: Given data: Outlet enthalpy (h2) = (h1+70) kJ/kg Work required for the compressor (W) = -175 kJ/kg…

Q: A tea maker whose top (1 point) is open to the atmosphere is completely full. The tea flows from the…

A: we will use Bernoulli's equation to solve this problem p1ρg+v122g+z1=p2ρg+v222g+z2

Q: convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible.…

Q: On the bases of the units of the quantities involved, show that the mass flow rate of air (in kg/s)…

A: The mass flow rate is written as follows: ṁ = M/t……. (1) Here, M is the mass, and t is the time.…

Q: Determine the mass flow rate (kg/hr) of fluid in a vertical tank 2 m. in diameter and 4 m. high,…

Q: Fluid X56-1 (density = 1300 kg/m3; M = 253 kg/kmol) is pumped at a rate of 4.58 m3/hour from a…

A: Since you have put a multi-part question which contain more than three sub-parts, thus we are able…

Q: The water level in a tank is 20 m above the ground. A hose is connected to the bottom of the tank,…

A: Draw a diagram for the problem. Here, Patm is the atmospheric pressure, h is the height up to which…

Q: When designing forced hot water heating system for a residential building, which of the following…

A: Given Diameter of the pipe = 40 mm = 0.04 m Density of water = 983 kg/m3 To find Mass flow rate

Q: Consider a pump system that delivers water at a flow of Q = 5 cubic feet per second (cfs) in a steel…

Q: A lubricating oil of viscosity 1 poise and specific gravity 0.9 is pumped through a 30 mm diameter…

Q: Determine the friction contributed by a half-open globe valve if the flow of water through it is at…

Q: Constant operating speed characteristics; H = 55 – 460v² and ng = 8,2v – 130v³ Water is drawn from a…

Q: A boiler house has natural draught chimney of 20 m height. Flue gases are at temperature of 380°C…

A: Data given- H = 20 m Tg = 380 °C = 653 K Ta = 27°C = 300 K

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop systems.
Define the overall efficiency of a turbine– generator is the product of the efficiency of the turbine and the efficiency of the generator, and it represents the fraction of the mechanical power of the fluid converted to electrical power.
The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of fluid at the inlet are 3000kJ/kg and 220km/hr respectively. At the exit, the specific enthalpy of fluid is 2,7×10^6J/kg.Calculate (a) the velocity of the fluid at the exit of the nozzle in (m/s), (b)Determine the rate of flow of fluid (mass flow rate) when the inlet area is 0,2 m^2 and the specific volume at the inlet is 0,3m^3/kg, (c) Determine exit area of the nozzle when the specific volume at the nozzle exit is 0,6m^3/kg
Determine the static fan efficiency if total fan mechanical efficiency is 70% and air is measured at 25 deg C and 760 mmHg for a fan that draws 1.42 cubic meters of air per second at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter.
A fan is to be selected to ventilate a bathroom whose dimensions are 2 m × 3 m × 3 m. The air velocity is not to exceed 7 m/s to minimize vibration and noise. The combined efficiency of the fan–motor unit to be used can be taken to be 50 percent. If the fan is to replace the entire volume of air in 15 min, determine (a) the wattage of the fan–motor unit to be purchased, (b) the diameter of the fan casing, and (c) the pressure difference across the fan. Take the air density to be 1.25 kg/m3 and disregard the effect of the kinetic energy correction factors.
Water is flowing at a rate of 0.5 m³/s through a rough pipe with a diameter of 0.5 m and a length of 800 m. Assuming the average roughness height (k) is 0.15 mm, determine: a) the friction coefficient, b) the wall shear stress, c) the velocity at the centerline and 200 mm away from the pipe wall.
In a hydroelectric power plant, 100 m3/s of water flows from an elevation of 120 m to a turbine, where electric power is generated . The total irreversible head loss in the piping system from point 1 to point 2 (excluding the turbine unit) is determined to be 35 m. If the overall efficiency of the turbine–generator is 80 percent, estimate the electric power output.
In climates with low night-time temperatures, an energy-efficient way of cooling a house is to install a fan in the ceiling that draws air from the interior of the house and discharges it to a ventilated attic space. Consider a house whose interior air volume is 720 m3 If air in the house is to be exchanged once every 20 minutes, determine (a) the required flow rate of the fan and (b) the average discharge speed of air if the fan diameter is 0.5 m..
A differential thermocouple with sensors at the inlet and exit of a pump indicates that the temperature of water rises 0.048° F as it flows through the pump at a rate of 1.5 ft3/s. If the shaft power input to the pump is 23 hp and the heat loss to the surrounding air is negligible, determine the mechanical efficiency of the pump.
Subject : Thermofluid Question : Water enters a hydraulic turbine through a 40-cm diameter pipe at a rate of 0.6 m3/s and exits through a 25-cm diameter pipe as shown by Figure 2. The pressure drop in the turbine is measured by a mercury manometer to be 1.4 m. For a combined turbine–generator efficiency of 80 percent and disregarding the effect of the kinetic energy correction factors.Determine the net electric power output. [Note: Take the density of water to be 1000kg/m3]
Oil is pumped from a very large tank (z1 = 150 m) to another tank (z2 = 200 m), located higher and with a cross-sectional area of A = 0.02 m2. Both tanks are open to the atmosphere. The efficiency of the pump in the system is 78% and its power is 185 kW. Friction losses between two points are ΣF = 117.7 N.m / kg. Calculate the mass flow rate (M) of the oil in the pipe in kg / s (density of the oil ρ oil = 870 kg / m3; α = 1; g = 9.81 m / s2; gc = 1 kg.m / N.s2).
Explain the the mechanical efficiency of a fan is the ratio of the rate of increase of the mechanical energy of air to the mechanical power input.