4. Chapter 10, Problem 47, page 328. This problem describes one experimental method for determining the moment of inertia of an irregularly shaped object such as the payload for a satellite. Figure P10.47 shows a counterweight of mass m suspended by a cord wound around a spool of radius r, forming part of a turntable supporting the object. The turntable can rotate without friction. When the counterweight is released from rest, it descends through a distance h, acquiring a speed v. Show that the moment of inertia I of the rotating ( 2gh apparatus (including the turntable) is mr² (20n – 1). v2

4. Chapter 10, Problem 47, page 328. This problem describes one experimental method for determining the moment of inertia of an irregularly shaped object such as the payload for a satellite. Figure P10.47 shows a counterweight of mass m suspended by a cord wound around a spool of radius r, forming part of a turntable supporting the object. The turntable can rotate without friction. When the counterweight is released from rest, it descends through a distance h, acquiring a speed v. Show that the moment of inertia I of the rotating ( 2gh apparatus (including the turntable) is mr² (20n – 1). v2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

[20] A crane that is 10 meters long is rotating (while loaded), at 1 radians/sec. It is stopped instantly (in 0.1 radian) in the position shown. Due to momentum the load continues to swing. Ignoring the deflection of the crane for this problem. (list all assumptions). The load is 750 lbs. a) The weight of the 10 m crane boom is 3000 lb and the mass moment of inertia is 80 lb ft s^2 about the centroid. Using the parallel axis theory find the mass moment of inertia around the point of rotation. Parallel axis theory can be found in appendix B formula B.6 (pg A9). b) Determine the maximum VERTICAL distance through which the load will swing. (Use the principle of work and energy with the work done by the weight. Two positions needed). c) What is the normal acceleration of the weight immediately after the crane stops (magnitude and direction)? d) What is the maximum energy that can be transmitted back to the crane (boom and load)? e) What forces and moments are there on the boom at the point…
A weight of 500 kg is being lifted up at a uniform speed of 1.5 m/s by a winch driven by a motor running at a speed of 1000 rpm. The moments of inertia of the motor and winch are 0.3 and 0.3 kg-m respectively. In the absence of the weight, the motor develops a torque of 100 Nm at a speed of 1000 r/min. Calculate the motor torque and the equivalent moment of inertia referred to the motor shaft
A turntable is a uniform disc of mass 2 kg and radius 1.3 x 10-1 m. The turntable is spinning at a constant rate of = 0.5 . The motor is turned off and the turntable slows to a stop in 8.0 s with constant angular deceleration. Find the (a) moment of inertia of the turntable; (b) initial rotational kinetic energy; (c) angular deceleration of the turntable while it is slowing down; (d) total angle in radians that the turntable spins while slowing down; and (e) magnitude of the frictional torque.
A crane that is 10 meters long is rotating (while loaded), at 1 radians/sec. It is stopped instantly (in 0.1 radian) in the position shown. Due to momentum the load continues to swing. Ignoring the deflection of the crane for this problem. (list all assumptions). The load is 750 lbs. a) The weight of the 10 m crane boom is 3000 lb and the mass moment of inertia is 80 lb ft s^2 about the centroid. Using the parallel axis theory find the mass moment of inertia around the point of rotation. b) What forces and moments are there on the boom at the point of rotation?
A flywheel of mass 0.9 ton is fitted to a multi cylinder engine, which runs at a mean speed of 380 r.p.m. If the speed varies from 9 % above the mean to 6 % below it and the fluctuation energy is 1100 kN-cm, find (i) mass moment of inertia of the wheel and (ii) radius of Gyration.
Two blocks are attached by strings of negligible mass to a physical pulley with two radii R1=027 m and R2=042 m. The strings are wrapped around their respective radii so that the masses can move either up or down. The pulley has a moment of inertia Ipcm=0249 kgm2, and is supported by a bearing with negligible friction. If block 1 has a mass of m1=4.1 kg, block 2 has a mass of m2=1.14 kg, and the tension in the rope connecting block 1 to the pulley is T1p=31.11 N, what is the magnitude of the angular acceleration of the pulley?
Suppose a 30 lb truck wheel 18 in. in diameter has a radius of gyration of 4 in. and the 6120 lb truck’s weight is distributed equally to each of the four wheels.a. If the truck can supply 150 lb x ft of torque to each wheel, how fast would the wheel want to accelerate if it didn’t slip? b. What would the coefficient of friction have to be in order to keep the wheel from slipping
Derive the equations of motion of the block of mass m1 in terms of its displacement x. Surface frictions and pulley inertia are negligible, the cylinder has a mass of m2 and doesn’t slip.
A mass weighing 11.5 kg falls a distance of 1.5 m upon the top of a helical compression spring. Determine the force applied on the spring if it compressed 203mm. Please show your full solution with unit analysis. Subject: Machine Design
A drum can rotate about a fixed-point O. The A block is attached to a cord wrapping around the drum. The mass of the drum is md = 100kg and the radius is r = 0.5 m. The radius of gyration of the drum about point O is ko=0.3 m. The mass of the block is mb= 20kg. The block is released from rest. The acceleration due to gravity is g=9.81 m/s2. (1) Calculate the mass moment of inertia of the drum about the point O, IO_______(kgm2) (two decimal places)
A uniform beam of length, L, and mass, M, is freely pivoted at one end about an attachment point in a wall. The other end is supported by a horizontal cable also attached to the wall, so that the beam makes an angle phi with the horizontal as shown below. To answer the questions below, find algebraic expressions for the tension in the cable, the angular acceleration of the beam, should the cable break, and the resulting angular velocity as the beam falls through the vertical position. A. If L = 2.4 m, M = 5 kg, and phi = 45o, then what is the tension in the cable? B. If the cable snaps, what is the angular acceleration about the pivot point? C. What is the angular velocity of the falling beam, just as it hits the wall?
The radius of the flywheel given in the figure is 600 mm. Its mass is 144The radius of rotation (inertia) of the flywheel, which is kg, is 450 mm. to a mass of 18 kgObject A is suspended from a rope wrapped around the flywheel. system is stagnantbeing released in the (still) state. Object A 1.8 meters downFind the acceleration and velocity of the block when it moves straight.