4. The maximum force exerted by a small hydraulic press is 500 kN. The working pressure of the fluid is 20N/mm?. Determine the diameter of the plunger, operating the table. Also suggest the suitable thickness for the cast steel cylinder in which the plunger operates, if the permissible stress for cast steel is 100 MPa.

4. The maximum force exerted by a small hydraulic press is 500 kN. The working pressure of the fluid is 20N/mm?. Determine the diameter of the plunger, operating the table. Also suggest the suitable thickness for the cast steel cylinder in which the plunger operates, if the permissible stress for cast steel is 100 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The thick walled cylinder of a hydraulic system is acted by a hydraulic pressure of 370 psi while themaximum load of the piston is 5500 lbs. If the allowable tensile stress is 2 ksi, find the required wallthickness of the cylinder.
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?
Question twoa) Shafts and tubes having circular cross sections cannot be used to transmit powerdeveloped by a machine. True or False? b) Explain the concept of torsion. c) If the applied torque on shaft CD is T = 75 N.m, determine the absolute maximumshear stress in each shaft. The bearings B, C, and D allow free rotation of the shafts,and the motor holds the shafts fixed from rotating
The motor A delivers 7500 kW to the shaft at 3600 rev/min, of which 2500 kW is removed by gear B and 5000 kW is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G = 83 GPa for steel, and assume that friction at bearing D is negligible. Show complete solution, and the free body diagram.
For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
The outside diameter of the coils of a safety valve spring is 120 mm while its wire diameter is 15 mm. This spring, having 10 active coils has the ends in plain ground, and has a free length of 200 mm. 1. Determine the length (in mm) at which this spring must be initially compressed to hold a pressure of 1400 kPa applied on a 32-mm diameter valve seat. Use a modulus of rigidity of 80 GPa. 2. calculate the spring’s maximum stress induced if it is compressed to its solid length
A cylindrical steel pressure vessel has hemispherical emd caps. The inner radiuos of the vessel is 24 in anf the wall thickness is constant at o.25 in. When the vessel is presseured to 125 psi determine the following. A. The stresses of the cylinder r and hemispgerical caps. B. Based from the allowable working pressure of the blvessel solved in item a, if the pressure is increased to 250 psi what shall be the uniform thickness of the tank
The outside diameter of the coils of a safety valve spring is 120 mm while its wire diameter is 15 mm. This spring, having 10 active coils has the ends in plain ground, and has a free length of 200 mm. A.Determine the length (in mm) at which this spring must be initially compressed to hold a pressure of 1400 kPa applied on a 32-mm diameter valve seat. Use a modulus of rigidity of 80 GPa. B. Calculate the spring’s maximum stress induced if it is compressed to its solid length.
The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm. Find the maximum shear stress in the cylinder for an internal pressure of 221 MPa.
Find the compressive stress at the head as the bolt bears on the surface to resist the tensile load.
simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 mm outside diameter with threaded ends. What will be the nominal stresses set up in the tube and the rods, ignoring thread depth, when the turnbuckle carries an axial load of 30 kN? Assuming a sufficient strength of thread, what maximum load can be transmitted by the turnbuckle if the maximum stress 1s limited to 180 MN/m*?
When drilling a well at a constant angular velocity, the bottom end of the drill pipe encounters a torsional resistance TA. Also, soil along the sides of the pipe creates a distributed frictional torque along its length, varying uniformly from zero at the surface B to tA at A. Determine the minimum torque TB that must be supplied by the drive unit to overcome the resisting torques, and calculate the maximum shear stress in the pipe. The pipe has an outer radius ro and an inner radius ri.