simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 mm outside diameter with threaded ends. What will be the nominal stresses set up in the tube and the rods, ignoring thread depth, when the turnbuckle carries an axial load of 30 kN? Assuming a sufficient strength of threa

simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 mm outside diameter with threaded ends. What will be the nominal stresses set up in the tube and the rods, ignoring thread depth, when the turnbuckle carries an axial load of 30 kN? Assuming a sufficient strength of threa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.32P

See similar textbooks

Similar questions

A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with closed ends (see figure). The fabric and plastic structure is inflated by a small blower and has a radius of 40 ft when fully inflated. A longitudinal scam runs the entire length of the "ridge" of the structure. If the longitudinal scam along the ridge tears open when it is subjected to a tensile load of 540 pounds per inch of seam, what is the factor of safety n against tearing when the internal pressure is 0,5 psi and the structure is fully inflated?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A steel bolt 25 mm in diameter carries a load of 4 kN in tension. Estimate the tensile stress of the section A and at the screw section B when the diameter of the thread is 20 mm.
PROBLEM 2A tri metallic bar is uniformly compressed by an axial force P=12kN applied through a rigid end plate. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter 10mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm. E for steel =210Gpa, E for brass =100GPa and E for copper is 120GPa. Calculate the compressive stress of each metal due to force P.
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
Problem 1 only, solve carefully, include the units and dra the diagram. Thanks! . A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850 in-lb. The shaft diameter is 1.75inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, findA. Force that will shear the pin, kNB. Shear pin diameter, mm
A compound tube consists of a steel tube 120 mm internal diameter and 140 mm external diameter and an outer brass tube 140 mm internal diameter and 10 mm thickness. The two tubes are of the same length equal to 150 mm. The compound tube carries an axial load of 800 kN. Estimate the stresses and the load carried by each tube and the amount it shortens. Take E for steel as 2 × 105 N/mm2 and for brass as 1 × 105 N/mm2.
A shaft 80 mm diameter transmits the power at maximum shear stress of 63MPa. Find the length of a 20mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42MPa.
A lap joint, consisting of 250 mm × 75 mm wooden plates, is fastened with two(2) rows of 20 mm diameter rivets . There are three(3) rivets in a row. The working stresses are 70MPa for rivets in shear and 140 MPa for plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.