47. A simple beam 20' in length supporting a point load of 5,000 lb 5' from the left support and another point load of 1,000 lb in the center of the beam. The beam is supported by a fixed connection on the left and a bearing connection on the right. 5.000 5.0 20.0 1000 10-0

Q: Assuming that 30% of the rainfall runs off, the volume of runoff (acre-feet) from a storm with a…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Solve for the reactions and draw the shear and moment diagram. (1) (3) (5) (7) (9) (11) 10 kN-m 10…

A:

Q: A wide, shallow sand-bed channel has a slope of 0.00105 (assume smooth channel banks). The average…

A: I am solving 5th question as per bartleby guidelines one question

Q: A highway designed for 80 km/h speed has a horizontal curve section with radius 250 m. If the design…

A: Given: Design speed = 80Kmph Radius =250m Lateral friction fully developed Required: Superelevation

Q: A wide, shallow sand-bed channel has a slope of 0.00105 (assume smooth channel banks). The average…

A: Given, Vs = 4.5 cm/s u* = 0.323 ft/s

Q: The direct and indirect costs estimated by a contractor for bidding a project is Rs. 160000 and Rs.…

A: Using formula

Q: The best method of interpolation of contours, is by Graphical means O all the above O Computation O…

A: Answer :  Computation The best method of interpolation of contours, is by computation. More…

Q: Draw the shear force and bending moment diagrams of the cantilever beam shown using METHOD OF AREAS.…

A: Solution No horizontal force, so HA = 0 Σ Fy = 0 VA + VB + VD = (12×5×12) + (12×10) VA + VB + VD =…

Q: 5. Consider a composite shaft fabricated from a 6 cm-diameter solid aluminum alloy, having G = 28…

A: As per company's guidelines we can only answer first three questions.  Kindly post other questions…

Q: 6-15. Members AB and BC can each support a maximur compressive force of 800 lb, and members AD, DC,…

A: Given : Max load that can be supported by AB and BC members = 800 lb Max load that can be supported…

Q: Problem-5 A partially open sluice gate discharges water at 6 m/s with a depth of 40 cm in a…

A: Given data- Velocity V=6 m/s, Depth y1=40 cm=0.40 m, Width B=5 m, g=10 m/s2. To Find- Post jump…

Q: 2. A solid shaft of 150 mm radius is used to transmit torque. Find the maximum torque transmitted by…

A:

Q: compute the azimuth and bearing of the remaining lines. Draw the figure

A: ###Computation of Azimuth and Bearing of the remaining lines####

Q: many futuristic projection system types, together with their parts and purposes What are they…

A: In order to aid navigators at sea and on land, maps have been created of the trade routes, local…

Q: A 0.82 of 264

A:

Q: six-lane urban freeway (three lanes in each direction) is on rolling terrain with 11-ft lanes,…

A:

Q: (6a) A siphon is made of a pipe whose inside diameter is 25.4 mm and is used to maintain a constant…

A: Data given Siphon pipe, diameter = 25.4 mm = 0.0254 m Depth of tank = 6.0975 m

Q: For true difference in elevations between two points A and B, the level must be set up at any point…

A:

Q: Two installers will install the unit. Each will work the same amount of timeand will be paid $8.00…

A: Given:- paid amount=$8.00 per hour two installers each work same amount of time To find:- how much…

Q: The coordinates closed traverse ABCDE are: (0,0),B (170, 320),C (470, 90), D (340, -110), E (-40,…

A: Using formula

Q: The curvature of the beam at the mid-span

A: ###Determination of Curvature of Beam at Mid Span ###

Q: A level was set up in the middle of two pegs A and B and the staff readings were 2.015 and 1.895…

A:

Q: In an Oedometer apparatus, a specimen of fully saturated clay has been consolidated under a vertical…

A: Given:- The vertical pressure on the fully saturated clay = 50 kN/m2  The increased vertical stress…

Q: The basketball player likes to release his foul shots with an initial speed vo = 23.5 ft/sec. What 2…

A:

Q: Calculate the tensile steel strain of 5-16-mm-dia rebars in a concrete beam 200 mm by 440 mm at…

A:

Q: A series levelling had been down along the centre line of the proposed road the distance between…

A:

Q: Q2: The solid rod shown in the Figure has a radius of (20 mm). If it is subjected to the forces of…

A:

Q: Stadia Tacheometric Survey Problem 3. In the figure, the difference in elevation between observed…

A:

Q: Specify cloth area per compartmeat, ft2.

A: Given data:- The given air is flowing at, 145000 acfm at 1 atm The given temperature is, 220°F

Q: Hydrographic surveys deal with the mapping of heavenly bodies O large water bodies O canal system O…

A: Ther are many types of surveying  such as:  Land survey Hydrographic survey Astronomical survey…

Q: A particle moving in the x-y plane has a position vector given by r = 3/2t² i + 2/3t³j, where r is…

A:

Q: A and B are two stations Whose coordinates are (585.1 E,1056.9N), (992.7 E,1426.5 N) Find Length and…

A: Surveying: to determine length and direction of AB

Q: A farm pond having full capacity of 125 m3 was emptied to a 2-ha farm through a connecting canal in…

A:

Q: A projectile is launched with a speed vo = 24.4 m/s from the floor of a 4.6-m-high tunnel as shown.…

A:

Q: 11. Determine the unknown bearings for the traverse courses shown in Figure A. 89°38' 96°11' N83…

A:

Q: mber In a lined rectangular canal, the Froude hl of incoming flow is 3.0. A hydraulic jump forms…

A:

Q: A plate 0.025 mm distant from a fixed plate, moves at 60 cm/s and requires a force of 2N/m² to…

A:

Q: 4k/ft 20 k B

A:

Q: 2. An archaeologist took some measurements on the unique mountain he had found. He sets two points X…

A:

Q: The Pratt bridge truss is subjected to the loading 6-30. shown. Determine the force in members JI,…

A:

Q: If + 0.8% grade meets - 0.7% grade and the rate of change of grade for 30 m distance is 0.05, the…

A: Using formula

Q: answer the following problems using method of joints and method of section separately in solving for…

A: To find stress in member BC,BD,CF

Q: Q4: Determine the maximum deflection and its location of the simply supported beam shown in the…

A: E = 200Gpa   I = 65×106 mm4I = 65×10-6m4EI = 200×109 ×65×10-6 = 1.3×107N-m2EI = 13000 kN-m2 Beam is…

Q: nalyze the beam by drawing the shearing force oment equations. rite your solutions legibly and…

A:

Q: 6-1 1. Compute the DMD of line 3-4. 2. Compute the length of line 6 to 1. 3. Compute the bearing of…

A: To find DMD of line 3-4 Length of line 6-1 Bearing of line 6-1

Q: The direct and indirect costs estimated by a contractor for bidding a project is Rs. 160000 and Rs.…

A:

Q: 02: A composite made from carbon reinforced epoxy has a diameter 2.5 cm, length 1.25 m, and mass…

A: Objective: To determine- 1) Volume fraction of carbon fibers and epoxy matrix 2) Modulus of…

Q: 6. A pump supplies water under pressure to a large tank. The circular-plate valve on the discharge…

A:

Q: Two roads AB and BC intersect at a chainage 184+65. These are intersected by a line PQ and the…

A:

Q: An aluminium shaft with a constant diameter of 50 mm is loaded by torques applied to gears attached…

A:

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.