5-39 Air at 1 atm and 300 K blows across a 50-cm-square flat plate at a velocity such that the Reynolds number at the downstream edge of the plate is 1.1×105. Heating does not begin until halfway along the plate and then the surface temperature is 400 K. Calculate the heat transfer from the plate. Heat transfer-Holman

5-39 Air at 1 atm and 300 K blows across a 50-cm-square flat plate at a velocity such that the Reynolds number at the downstream edge of the plate is 1.1×105. Heating does not begin until halfway along the plate and then the surface temperature is 400 K. Calculate the heat transfer from the plate. Heat transfer-Holman

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.65P

See similar textbooks

Similar questions

A 4-m x 4-m flat plate maintained at a constant temperature of 80°C is subjected to parallel flow of air at 1 atm, 20°C, and 10 m/s. The total drag force acting on the upper surface of the plate is measured to be 2.4 N. Using momentum heat transfer analogy, determine the average convection heat transfer coefficient, and the rate of heat transfer between the upper surface of the plate and the air
The weight of a thin flat plate 50 cm × 50 cm in size is balanced by a counterweight that has a mass of 2 kg, as shown. Now a fan is turned on, and air at 1 atm and 25°C flows downward over both surfaces of the plate (front and back in the sketch) with a free-stream velocity of 10 m/s. Determine the mass of the counterweight that needs to be added in order to balance the plate in this case.
During major windstorms, high vehicles such as RVs and semis may be thrown off the road and boxcars off their tracks, especially when they are empty and in open areas. Consider a 5000-kg semi that is 9 m long, 2.5 m high, and 2 m wide. The distance between the bottom of the truck and the road is 0.75 m. Now the truck is exposed to winds from its side surface. Determine the wind velocity that will tip the truck over to its side. Take the air density to be 1.1 kg/m3 and assume the weight to be uniformly distributed.
In a geothermal power plant, the used geothermal water at 80°C enters a 15-cm-diameter and 400-m-long uninsulated pipe at a rate of 8.5 kg/s and leaves at 70°C before being reinjected back to the ground. Windy air at 15°C flows normal to the pipe. Disregarding radiation, determine the average wind velocity in km/h.
The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure and 20°C flows with a velocity of 8 m/s over a 1.5 m * 6 m flat plate whose temperature is 140°C. Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 6-m-long side and (b) the 1.5 m side.
Write down the power-law velocity profile empirical correlation and when is this relation valid?
Metal plates (k = 150 W/m·K, ρ= 2800 kg/m3, and cp = 900 J/kg·K) with a thickness of 2 cm exiting an oven are conveyed through a 10-m long cooling chamber at a speed of 4 cm/s, as shown in the figure. The plates enter the cooling chamber at an initial temperature of 500°C. The air temperature in the cooling chamber is 15°C, and the plates are cooled with blowing air and the convection heat transfer coefficient is given as a function of the air velocity h(V) = 33V0.8, where h is in W/m2·K and V is in m/s. To prevent any hazard to workers handling the plates, it is necessary to design the cooling process such that the plates exit the cooling chamber at a relatively safe temperature of 50°C or less. Determine the air velocity V and the heat transfer coefficient h such that the temperature of the plates exiting the cooling chamber is at 50C.
Imagine a plate 0.1 m long by 0.1 m wide at a temperature of 80 °C. Water is passed over its surface at a speed of 0.1 m/s and 40°C. Calculate the heat dissipated by the plate. Assume the following properties of water at 60 °C: k= 0.651 W/mK, Pr=3.02 y v = 0.478 x 10-6 m²/s.
What is mean transport area? How can this be used in solving geometric considerations for mass, heat, and momentum transport problems?
A ball has a diameter of 28 mm and falls in honey with a terminal velocity of 0.3 m/s. For honey, take ρh = 1360 kg/m3 and νh = 0.04 m2/s. Note: The volume of a sphere is V ¯¯¯=43πr3
ENGINEERING MECHANICS The impulse and momentum principle is mostly useful for solving problems involving whatquantities? How is momentumcalculated? Whatis the first derivative of kinetic energy with respect to time? When will a three-force member be considered inequilibrium?
In the effort to increase the removal of heat from a hot surface at 120°C, a cylindrical pin fin (kf = 237 W/m.K) with diameter of 5 mm is attached to the hot surface. Air at 20°C (1 atm) is flowing across the pin fin with a velocity of 10 m/s. Determine the maximum possible rate of heat transfer from the pin fin. Evaluate the air properties at 70°C.