5-83* The 1/2-in.-thick bar with semicircular (d/r = 1) edge grooves, shown in Fig. P5-83, is made of structural steel and will be subjected to an axial tensile load P of 10 kip. Determine the minimum safe width B for the bar if the maximum normal stress is limited to 20 ksi. į in. P B b r=} in. 글 in.

5-83* The 1/2-in.-thick bar with semicircular (d/r = 1) edge grooves, shown in Fig. P5-83, is made of structural steel and will be subjected to an axial tensile load P of 10 kip. Determine the minimum safe width B for the bar if the maximum normal stress is limited to 20 ksi. į in. P B b r=} in. 글 in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.9P: Because of foundation settlement, a circular tower is leaning at an angle a to the vertical (see...

See similar textbooks

Similar questions

A steel post /t if with a hollow circular cross section is fixed at the base and free at the top (see figure). The in net and outer diameters arc d1= 96 mm and d2= 110 mm, respectively, and the length is L = 4.0 m. A cable CED passes through a fitting that is welded to the side of the post. The distance between the plane of the cable (plane CBD) and the axis of the post is e = 100 mm, and the angles between the cable and the ground arc a = 53.13º. The cable is preten-sioned by tightening the turn buck les. If the deflection at the top of the post is limited to = 20 mm, what is the maximum allowable tensile force Tin the cable? (Assume E = 205 GPa.)
The shear stresses t in a rectangular beam arc given by Eq. (5-43): in which Fis the shear force, / is the moment of inertia of the cross-sectional area, /lis the height of the beam, and i] is the distance from the neutral axis to the point where the shear stress is being determined (Fig. 5-32). By integrating over the cross-sectional area, show that the resultant of the shear stresses is equal to the shear force V.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A vertical pole of aluminum is fixed at the base and pulled at the top by a cable having a tensile force T(see figure). The cable is attached at the outer edge of a stiffened cover plate on top of the pole and makes an angle a = 20° at the point of attachment. The pole has length a = 2.5 m and a hollow circular cross section with an outer diameter d2= 280 mm and inner diameter d1= 220 mm. The circular cover plate has diameter 1.5d2 Determine the allowable tensile force Tallow in the cable if the allowable compressive stress in the aluminum pole is 90 MPa.
A retaining wall (Fig. a) is constructed using steel W-shape columns and concrete panel infill (Fig, b). Each column is subjected to lateral soil pressure with peak intensity q0(Figs, b and c). The tensile and compressive strength of the beam is 600 MPa. Select the most economical W 360 section from Table F-l(b) based on safety factor of 3.0.
Because of foundation settlement, a circular tower is leaning at an angle a to the vertical (see figure). The structural core of the tower is a circular cylinder of height ft, outer diameter d2, and inner diameter d1.For simplicity in the analysis, assume that the weight of the tower is uniformly distributed along the height. Obtain a formula for the maximum permissible angle a if there is to be no tensile stress in the tower.
The figure shows an idealized structure consisting of rigid bars ABC And DEF joined by a linearly elastic spring ß between C and D. The structure is also supported by translational elastic support ß at B and rotational elastic support ßRat E. Determine the critical load Pcrfor the structure.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.