5) A horizontal water jet of constant velocity V impinges normally on a vertical flat plate and splashes of the sides in the vertical plane. The plate is moving toward the oncoming water jet with velocity V /2 (see figure below). If a force F is required to maintain the plate stationary, how much force is required to move the plate toward the water jet? Water jet

5) A horizontal water jet of constant velocity V impinges normally on a vertical flat plate and splashes of the sides in the vertical plane. The plate is moving toward the oncoming water jet with velocity V /2 (see figure below). If a force F is required to maintain the plate stationary, how much force is required to move the plate toward the water jet? Water jet

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the incompressible flow of water through a divergent duct, where the inlet has a velocity & section area of 5 ft/s & 10 ft2. If the exit area is 5x the inlet area and the density of water is 62.4 lbm/ft3, solve for the pressure difference. (Please type answer no write by hend)
Water falls vertically downward from an open faucet with an initial velocity of 66 cm/s. If the stream diameter at the faucet head is 0.5 cm what is the stream diameter at a distance 5 cm below the faucet exit?
In Fig. water exits from a nozzle into atmosphericpressure of 101 kPa. If the fl ow rate is 160 gal/min, what isthe average velocity at section 1?( a ) 2.6 m/s, ( b ) 0.81 m/s, ( c ) 93 m/s, ( d ) 23 m/s, ( e ) 1.62 m/s
A 3-in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which deflects the water 180 degrees at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream. Please no conversion need it, only the 3in into .25feet, please. for me, I got 3.71KN on the x-axis.
In Fig. water exits from a nozzle into atmosphericthe pressure of 101 kPa. If the exit velocity is V 2 = 8 m/s andfriction is neglected, what is the axial fl ange force requiredto keep the nozzle attached to pipe 1?( a ) 11 N, ( b ) 56 N, ( c ) 83 N, ( d ) 123 N, ( e ) 110 N
Water fl ows steadily through the box in Fig. P3.63. Averagevelocity at all ports is 7 m/s. The vertical momentum forceon the box is 36 N. What is the inlet mass fl ow?
If a jet is inclined upward 30O from the horizontal, what must be itsvelocity to reach over a 3-m wall at a horizontal distance of 18 m,neglecting friction?
Water flows through a pipe of 0.0025 m^2size with a uniform velocity of 7m/s and flows out from an ariface at bottom at a rate 0.003 m^3/s. what is rate of change of mass of water in the tank?
A 5-cm-diameter horizontal jet of water, with velocity 30 m/s, strikes the tip of a horizontal cone, which deflects the water by 45° from its original direction. How much force is required to hold the cone against the water stream?
A water truck drives slowly around a construction site, spraying water to keep dust down. A pump maintains a constant pressure of 100 kPa, gage, and the water is dispersed through 20 spray nozzles, each of diameter 0.01 m. If the truck is initially filled with 4000 L of water, and the flow rate is constant, determine how long the truck can drive before a refill is necessary in seconds.
Figure shows two points a half-period apart in theoperation of a pump. What type of pump is this ? Howdoes it work? Sketch your best guess of flow rate versustime for a few cycles.
Airstream flows in a converging duct from a cross-sectional area A1=50cm2to across-sectional area A2=40cm2. If T1=300K, P1=100kPa, and V1=100m/s, find area throat, velocity in throat and temperature in throat.