(5) A pickup truck has a five liter, V6, SI engine operating at 2400 r.p.m. the compression ratio rc = 10.2:1, the volumetric efficiency y = 0.91, and the bore and stroke related as stroke S = 0.92 B. calculate :- (a) stroke length. (cm) (b) Average piston speed. sec (c) Clearance volume of one cylinder. (cm³) kg (d) Air flow rate into engine. sec m

(5) A pickup truck has a five liter, V6, SI engine operating at 2400 r.p.m. the compression ratio rc = 10.2:1, the volumetric efficiency y = 0.91, and the bore and stroke related as stroke S = 0.92 B. calculate :- (a) stroke length. (cm) (b) Average piston speed. sec (c) Clearance volume of one cylinder. (cm³) kg (d) Air flow rate into engine. sec m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If an engine has a bore of 0.1 m, stroke of 0.08 m, inlet flow effective area of 4.0 × 10−4 m2, and inlet temperature of 320 K, what is the maximum speed it is intended to be operated while maintaining good volumetric efficiency?
A Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.
3. The nominal power of the wind turbine is 3MW at wind speed 11.5m/s, generator efficiency is 94%, gear box efficiency is 0.75, power coefficient of blades is 0.59. What would be the diameter of the rotor?
For a single acting reciprocating pump, piston diameter is 150 mm, stroke length is 300 mm, and rotational speed is 50 r.p.m. The pump is required to lift water to a height of 18 m. Determine the theoretical discharge. If the actual discharge is 4.0 lit./sec, and the mechanical efficiency is 80% determine the volumetric efficiency, slip, theoretical power and the actual power required.
A 6.4-liter, V8 Spark ignition (8 cylinder) 4-stroke engine operates at an engine speed of 3200 RPM. The compression ratio is CR = 10.5:1. At this speed volumetric efficiency is 93%, combustion efficiency is 98%, indicated thermal efficiency is 47%, and mechanical efficiency is 86%. Stroke and bore will be related by S = 0.90 B. Combustion starts at 18 degrees bTDC and last for 0.25 seconds. Calculate? a.Overall efficiencyb. Piston displacementc. Cylinder bore and stroked. average piston speed and max piston speede.distance piston has traveled from TDC at the end of combustion, f. volume at the end of combustion g. position of crank at the end of combustion
A propeller type, horizontal axis wind turbine having following wind characteristics: Speed of the wind 10 m/s at 150 C, The turbine has diameter of 120 m and its operating speed is 40 rpm at maximum efficiency. Calculate (i) the total power density in the wind stream (ii) the maximum obtainable power density assuming wind power coefficient as 40% (iii) total power produced in kW (iv) Maximum thrust and axial thrust. [Ans: 613 W/m2, 2771 kW, 6930 kW, 619.9510 kN, 897 kN] explain the axial thrust part clearly how 897 KN is coming
. A six-cylinder two-stroke cycle marine diesel engine with 100 mm bore and 120 mm stroke delivers 200 B.H.P. at 2000. R.P.M. and uses 100 kg of fuel per hour. If I.H.P. is 240, determine the following: (a) Torque, (b) Mechanical efficiency, (c) Indicated specific fuel consumption.
A 1:10 model of a Francis turbine developed 0.5 kW under a head of 2.5 m at 480 rpm. The physical data are r1=1.5m, r2 = 0.4m, α1=15°, β2=135°. Find the speed of the prototype at a head of 20m.
HANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution. An experimental gas turbine engine is under development to increase its mechanical efficiency. It has a turbine efficiency of 95% and compressor efficiency of 85%. The following parameters are provided: P1 = 550 kPa, T1 = 25 deg C, rp = 5.5, T3 = 1450 deg C, Wnet = 5500 kW. Compute for the (a) flow rate and (b) mean effective pressure. Consider Ethane as your working fluid.
A four-stroke gasoline engine produces an output of 40kW. Estimate the engines's rate of fuel consumption. Express your answer in liters per hour and gallons per minute
a. Given the static head of 28.91 m, and static pressure head of 3.15 cm WC. What is the normal pressure, Pn? b. What is the Static efficiency of the fan if the air flow rate is equal to 3.8 5m /sec, total head of 68.72 m, velocity head of 30.86 m, mechanical efficiency and power are 39.12% and 35.72 KW at 30.69°C, respectively. c. Solve for the area at entrance of the fan blade, if the it has a 346mm diameter, flow of air is equal to 23.328 m/se and flow rate of 3.05 m³ /second.
The wind turbine gives the following data: Blade length, l = 39 m, Wind speed, V= 12.4 m/s, Air density, ρ = 1.23 kg/m3 , Power Coefficient, Cp = 0.39, Calculate the power available in the wind.