5. A coil of inductance 0.1 H and negligible resistance is connected in series with a 25 N resistor. The circuit is energized from a 230 V, 50 Hz source. Calculate: (a) the current in the circuit; (b) the p.d. across the coil; (c) the p.d. across the resistor; (d) the phase angle of the circuit. Draw to scale a phasor diagram representing the current and the component voltages.

5. A coil of inductance 0.1 H and negligible resistance is connected in series with a 25 N resistor. The circuit is energized from a 230 V, 50 Hz source. Calculate: (a) the current in the circuit; (b) the p.d. across the coil; (c) the p.d. across the resistor; (d) the phase angle of the circuit. Draw to scale a phasor diagram representing the current and the component voltages.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Similar questions

A series circuit consists of resistance of 10 ohm, an inductance of 200/π mH and capacitance of 1000/π μF . Calculate (a) the current flowing in the circuit if supply voltage is 200 V, 50 Hz, (b) power factor of the circuit, (c) power drawn from the supply. Also draw the phasor diagram.
A 200V, 50 Hz sinusoidal supply is connected to a parallel network comprising three branchesA, B and C as follows: A, a coil of resistance 3 ohm and inductive reactance 4 ohm; B, a seriescircuit of resistance 4 ohm and capacitive reactance 3 ohm; C, a capacitor. Given that the powerfactor of the combined circuit us unity, find (a) the capacitance of the capacitor inF; (b) the current taken from the supply. [Ans. 127.32 F, 56A]
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage VR and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60Hz , R = 10 ohm Vcoil = 22.4 V. VR = 20 V and v = 36v , find the resistance and inductance of the coil.
An air-cored choking coil is subjected to an alternating voltage of 100 V. The current taken is 0.1 A and the power factor 0.2 when the frequency is 50 Hz. Find the capacitance which, if placed in parallel with the coil, will cause the main current to be a minimum. What will be the impedance of this parallel combination (a) for currents of frequency 50 (b) for currents of frequency 40?
A choke coil of resistance 8 ohm and inductance 0.15 H is connected in series with a capacitor of capacitance 125 ?? across a 230-V, 50- Hz supply. Calculate: (a) the inductive reactance, (b) capacitive reactance, (c) impedance, (d) current, (e) voltage across the coil and the capacitor, respectively. (f) phase difference between the current and the supply voltage.
An industrial coil is modeled as a series combination of an inductance L and resistance R, as shown in the figure below. Since an ac voltmeter measures only the magnitude of a sinusoid, the following measurements are taken at 60 Hz when the circuit operates in the steady state: Using the instruction provided, find R when E = 166 V, V1 = 80 V, VO = 101 V. Round off to 5 decimal places if applicable.
A coil of inductance 318.3 mH and negligible resistance is connected in series with a 200 ohm resistor to a 240V, 50 Hz supply. Calculate the inductive reactance of the coil, the impedance of the circuit, the current in the circuit, the p.d. across each component, and the circuit phase angle.
A factory has a large induction heater operating at 1000 V, 50Hz. The current flowing intothe heater is 12.33 A RMS and the true power is 10 kW b) Calculate the reactive power, apparent power and the power factor (PF) for this load.c) If the PF is lower than 0.9, explain the problem from an electrical perspective thencalculate how this load could be balanced practically.d) Draw a diagram to illustrate where the capacitor needs to be placed and what hashappened to the reactive current that was originally flowing from the inductive load backto the supplier? What are the specifications for this capacitor? What would such acapacitor cost? Who could supply this type of component?
Show your complete solution and attached it here. Answer must be in 4 decimal places. An industrial coil is modeled as a series combination of an inductance L and resistance R. Since an ac voltmeter measures only the magnitude of a sinusoid, the following measurements are taken at 60 Hz when the circuit operates in the steady-state: |Vs| = 145 V, |V1| = 50 V, |Vo| = 110 V Use these measurements to determine the values of L and R.
A coil has an inductance of 478µH.What is its reactance in 1000Hz ac circuit? 3.00ohms if connected in series with a resistor of 4.00ohms. What is the reactance of a 3.00microfaradcapacitor? What is the impedance of thecapacitor in series of 300ohms? What would be the current if the capacitorand resistor are connected in series with1200V line?
A coil RL is connected in series with a capacitor across the 220 V, 60 hz, AC supply. If this circuit operates at 0.87 pf leading, determine the magnitude of this voltage, Assume voltage acrros the coil and the caapacitor are equal.
A resistor'R' with resistance value of 24 ohm, an inductor 'L' with inductance 20mH, and a capacitor 'C' with capacitance 50 micro Farrad are connected in series with a AC voltage v(t) where v(t) = 50 cos (2 vt + 30 degrees) v. Determine the current i(t) and total impedance if the frequency f is i. 60 Hz ii. 400Hz