Hello,Need help with part b) Thank you, 5. a)For the beams shown below, draw the influence lines from points through for:i) bending moment at pointii) shear force immediately left of point, andiii) bending moment at pointFor each influence line, calculate and indicate the value of the influencecoefficient that has the maximum absolute value.to 4mDirection of Travel40kN40RN20kN4m+ 2m + 4m +IdealizedVehicledan5. b) A vehicle, which is idealized as three point loads shown on the left below, moves acrossthe beam structure shown. Calculate and show the influence line for shear force at pointB. Also calculate the largest shear force at the point that would occur while theidealized vehicle crosses the structure.2mL8m10m2m2mE6m

5. b) A vehicle, which is idealized as three point loads shown on the left below, moves across the beam structure shown. Calculate and show the influence line for shear force at point B. Also calculate the largest shear force at the point that would occur while the idealized vehicle crosses the structure. Direction of Travel 40kN 40RN 20kN +2m 4m - Idealized Vehicle A Am 8m √ 2 m | 11 2m 6m E

5. b) A vehicle, which is idealized as three point loads shown on the left below, moves across the beam structure shown. Calculate and show the influence line for shear force at point B. Also calculate the largest shear force at the point that would occur while the idealized vehicle crosses the structure. Direction of Travel 40kN 40RN 20kN +2m 4m - Idealized Vehicle A Am 8m √ 2 m | 11 2m 6m E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.
Draw the shear and moment diagrams given that Ra=110.2 kN, Rb=310.1 kN, Rc=220.6 kN, Ma=-124.5 kN m, Mb =-258.9 kN m, Mc = -160.5 kN
Determine the deflection at midspan of the structure Group of answer choices (-5wL^4)/384EI (5wL^4)/384EI (wL^3)/24EI (-wL^3)/24EI
To prevent the ladder weighing 600N from sliding down, the man exerts a horizontal force at C. The coefficient of friction at A= 0.2 while surface B is frictionless Find the vertical reaction at Aa. 600N c. 500Nb. 700N d. 800NFind the horizon reaction at Aa. 150N c. 210Nb. 180N d. 120NFind the horizon force exerted by the man at Ca. 533.3N c. 333.3Nb. 667.7N d. 767.6N
B. In Fig. below; rod AB rotates about an axis through A and s connected t0 block ) by a flexible and inextensible cable. Determine the linear velocity of block 1) when 0 = ' (3/4), and the angular velocity of AB is 2.5 ad/ sec counterclockwise. Fig2B B 15m,
Determine the horizontal force Q applied to block B that would cause the system to impend its motion to the left. (All contact surfaces have the same angle of friction of 11.31 degrees except the horizontal surface beneath block B with 16.7°)
Define the forces affecting to beam CDB when P = 600 N
Get the shear and moment function and drawthe shear and moment diagram for the beam.If the lower beam has a 8kN/m beam weightand upper beam has negligible weight.P1 = 400kNP2 = 60kNP3 = 190kN Note: draw a separate shear and momentdiagram for the upper and lower beam
A rectangular reinforced concrete beam with width of 300 mm & effective depth of 600 mm is subjected to a service bending moment of 200 kN.m. The beam is reinforced with 4-32 mm diameter bars. n = 8. 1. Compute the distance kd? a. 246.33 mm b. 353.67 mm c. 170.33 mm d. 302.33 mm 2. Which of the following gives the moment of inertia about N. A.? a. 4173.81 x 106 mm⁴ b. 3471.81 x 106 mm⁴ c. 4371.81 x 106 mm⁴ d. 4713.81 x 106 mm⁴ 3. Which of the following most nearly gives the maximum stress in steel in Mpa? a. 100 b. 110 c. 120 d. 130
The beam shown in the photo is used to support a portion of the overhang for the entrancewayof the building. Assume B is a roller and C is pinned. Draw the shear and moment diagrams forthe beam.
moment is 22kip.ft
A force F = (0.5i – 2.0j + 7.0k) kN acting at A(5, -4, 0)m about axis BC where B(6, 8, 4)m and C(-6, -5, 8)m. What is the perpendicular distance between F and the axis BC in meters?