Answered: 5. Determine he shear stress in the…

5. Determine he shear stress in the most heavily loaded 7/8-in-daimeter rivet in the joint shown in Fig. 5. T = 20 000 lb 20 deg. Centroid of connector group e = 2 in O Oo 3 in-3 in + 3 in Fig. 6.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing…

A: TRUSS:- is a rigid structure in which all he members are subjected to either axial or tensile or…

Q: applied as shown (F= 10KN). Compute the stress due to tension at each critical section (A, B, and C)…

Q: 9. Determine the width w of the plate loaded as shown if the 2000 N 10 mm permissible stress in…

Q: A square pedestal has glued parts at joints t, r, e, and s. Plane t-r-e-s is at anole of 30° from…

A: Given: The allowable compressive stress = 5.2 Mpa The inclination of plane = 30 degree The shear…

Q: Question 53 What is the elongation of the aluminum bar with a dimension of 25 mm by 25 mm and length…

Q: A solid aluminum shaft of 94 mm diameter fits concentrically in a hollow steel tube. Determine the…

Q: A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown…

A: For solution refer below images.

Q: The structure shown is made up of elements ABC, AD, BE, DF, joined by articulated connections at all…

Q: Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure…

A: Data given - P = 9 MPa r = 150 mm Or d = 2 × r = 2 × 150 = 300 mm t = 9 mm

Q: 8. A solid steel bar of diameter d, = M mm has a hole of diameter d2 = N mm drilled through it. A…

Q: The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be…

A: Given Data: Diameter of rivet, d=3/4 inch Working shear stress, 14000 psi Working bearing stress,…

Q: A supporting structure consists of a round steel bar with a welded square bar. The round bar is…

A: GIVEN: TO FIND:1. sketch the course of the required internal forces 2. necessary size b of the…

Q: 3) Specify a suitable size for the horizontal portion of the member that will maintain the combined…

A: Given data as per the question stress = 6000 psi Calculations Let 's' is the diameter of the cross…

Q: The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form…

A: To find: The greatest value of thrust and the stress along the face AB. Given: The tensile stress…

Q: A boiler with an outside diameter of 300 mm, length of 1000 mm and a wall thickness of 10 mm is…

A: According to the information we have a boiler with a diameter of 300 mm and a length of 1000 mm…

Q: - 540 mm 180 mm- 180 mm 60 mm → - B 30 kN

Q: A pivoting cantilevered chair support is proposed for an industrial equipment application. If the…

Q: A solid aluminum shaft of 112 mm diameter fits concentrically in a hollow steel tube. Determine the…

A: To find: The minimum internal diameter in mm of the steel tube. Given: The diameter of the shaft is…

Q: Module 4 Stress Distribution Point loads of 2000, 4000, and 6000 Ibs act at points A, B and C…

Q: Problem 8.5 A circular ring is subjected to a pull of 15 kN. The ring is of T-section as shown in…

A: A circular ring is known to be exposed to a 15 kN pull.The ring has a T-section, and the internal…

Q: A cantilevered structure has dimensions L=65-in, L-9.5-in, L=6.2-in, LF3.8-in and diameter d=2.5-in.…

A: Given L1 = 65 in L2= 9.5 in L3 = 6.2 in L4 = 3.8 in d1 = 2.5 in Fy = 78 lb Fz = 153 lb We have to…

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force. E4.png…

Q: A 50 mm diameter solid shaft is welded to a flat plate as shown in Fig. If the size of the weld is…

Q: D-1 A. solid circulár šhalit öf a the shaft B. the lap joint shown is fastend by three (20 )mm…

Q: A central horizontal section of a hook is a symmetrical trapezium of inner width =67.5mm and of…

A: Given:Inner width,bi=67.5 mmOuter width,bo=22.5 mmP=37.5 KNInner radius,Ri=52.5 mmh=90 mmOuter…

Q: The uniform 300-Ib bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B…

Q: A 50-kN force is subjected to a lap joint fastened by three 20-mm diameter rivets. (a) the shearing…

A: Given, P = 50 kN d = 20 mm

Q: The 20-mm-diameter bolt fastens two wooden planks together. The nut is tightened until the tensile…

Q: PROBLEM 2 Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working…

Q: (b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is…

Q: 3) Specify a suitable size for the horizontal portion of the member that will maintain the combined…

A: given; tensile force(F1)=400lbscompressive force(F2)=500lbscompressive and tensile…

Q: 1. The pipe shown below has a 1" outer diameter and a .125" wall thickness. Determine the state of…

Q: The lap joint is connected by three 20-mm-diameter rivets. Assuming that the axial load P=50 kN is…

A: Welding joints are used to join two different materials together. There are different types of…

Q: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN.…

Q: Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh .if the…

Q: Q1: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN.…

A: Q1:-

Q: QUESTION 2 с Y The 6.7-in diameter steel shaft AB is attached into the rigid wall at C and supported…

A: Given data: ◆ The dia meter of the shaft: d = 6.7 in ◆ The length of the lever AC: x = 3.54 ft ◆ The…

Q: A solid aluminum shaft of 100 mm diameter fits concentrically in a hollow steel tube. Determine the…

Q: span of 0.3m. A concentrated load of 250N is then applied vertically downwards at a point 0.1m from…

Q: Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown. A…

Q: Determine The Normal Stress In Each Member Of The Truss Structure Shown. 3. Material: Steel,…

A: The normal stress =43.56,52.9,49.6

Q: Problem 1A steel wire is 6 m long,, hanging vertically supports a load of 2000N. Neglecting the…

Q: 5. Determine he shear stress in the most heavily loaded 7/8-in-daimeter rivet in the joint shown in…

Q: Determine the thickness of a steel air receiver with 30 in. diameter and pressure load of 120 psi,…

Q: PROBLEM 2 Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa •…

A: Dear students The answer is given below---

Q: A 8 kN/m 35° OE D BỊ 20 kN 0.4 m 0.4 m 0.4 m

Q: QUESTION 4 A suspension cable passes over saddles supported by roller bearing on top of two towers…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

5. Determine he shear stress in the most heavily loaded 7/8-in-daimeter rivet in the joint shown
in Fig. 5.
T = 20 000 lb
20 deg.
Centroid of connector group
e = 2 in
O Oo
3 in-3 in + 3 in
Fig. 6.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The outside diameter of the steel pipe shown is 220 mm and its wall thickness is 6.0 mm. The upper bearing plate has the same width as the reinforced concrete beam it supports. The total load on the column by the reinforced concrete beam is 550 kN. Determine: A. The length L of the rectangular upper bearing plate if its width is 275 mm. and the average bearing stress between the steel plate and the reinforced concrete beam is not to exceed 6.2 MPa.
The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (sb)allow = 2 ksi, and the allowable tensile stress within the bolt shank S is (st)allow = 18 ksi, determine the maximum allowable tension in the bolt shank. The bolt shankhas a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
NEED ANSWER ASAP !!! The axial load 274 kN applied to the lap joint is distributed equally among the three 26.5-mm-diameter rivets. What is the bearing stress (in MPa) between a plate and a rivet if w = 135.4 mm and t = 29.5 mm?
A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm.Determine the average normal stress developed on the cross section if the load, F is1890 kN.
Link AB is to be made of steel for which the normal stress is 450 MPa. Determine the cross-sectional area of AB. Assume that the link will be adequately reinforced around the pins at A and B. draw free-body diagram
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
A flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm located at a 210 mm bolt circle diameter. Determine the flange thickness if the bearing stress on the flange is 95 MPa. A. 10 mm B. 20 mm C. 25 mm D. 30 mm
The bearings at A and D exert only y and z components of force on the shaft as shown in Fig 7. Determine the smallest diameter of the shaft using maximum shear stress hypothesis theory if the allowable stress is 100 MPa.
Downvote for incorrect answer The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (b)allow 2 ksi, and the allowable tensile stress within the bolt shank S is (allow 18 ksi, determine the maximum = allowable tension in the bolt shank. The bolt shank has a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
a.) Determine the reaction force at B and C b.) if average shear stress is not to exceed 160 MPa determine the minimum required diameter of the pin at B c.) if the diameter of the pin at C is 115 mm what is the average shear stress in the pin at C (four sig figs)
The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is w = 70 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 115 MPa, the bearing stress in the bar cannot exceed 140 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure.
Rank the normal stress in each section of the bar. Rank the values of normal stress from largest (largest tensile stress) to smallest (largest compressive stress). Use AB for segment AB, BC for segment BC, and CD for segment CD.