5. Each of the two elastic rubber bands of the slingshot has an unstretched length of 200 mm. If they are pulled back to the position shown and released from rest, determine the maximum height the 25-g pellet will reach if it is fired vertically upward. Neglect the mass of the rubber bands and the change in elevation of the pellet while it is

5. Each of the two elastic rubber bands of the slingshot has an unstretched length of 200 mm. If they are pulled back to the position shown and released from rest, determine the maximum height the 25-g pellet will reach if it is fired vertically upward. Neglect the mass of the rubber bands and the change in elevation of the pellet while it is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SHOW NEAT AND COMPLETE SOLUTION In the mass-pulley assembly shown, determine the velocity of block B at the instant when the velocity of block A is 1 m/s, directed downward.
15. If M0 = 400 kNm, determine the value of L so that the maximum deflection is 10 mm. 16. Determine if L = 8 meters, determine the value of M0 so that the maximum deflection is 10 mm. Solve for me all situations ok
5. End A of the 6kg uniform rod AB rests on the inclined surface, while end B is attached to collar of negligible mass which can slide along the vertical rod shown. Knowing that the rod is released from rest when ? = 35° and neglecting the effect of friction, determine immediately after release (e) The angular acceleration of the rod, (f) The reaction at B.
For the built-up shape shown in the figure, determine: a. The location of the plastic neutral axis from the top edge of the flange in mm (ANS 11). b. The plastic section modulus of about the horizontal axis in x106mm3 (ANS 0.214) c. The plastic moment with bending about the vertical axis if Fy = 345 Mpa kN-m. round of to the nearesrt whole number (ANS 43).
The 100-mm-diameter pulley shown fits loosely on a 10-mm-diameter shaft for which the coefficient of static friction is Determine the minimum tension T in the belt needed to (a) raise the 100-kg block and (b) lower the block. Assume that no slipping occurs between the belt and pulley and neglect the weight of the pulley Choices: A. TMAX = 1075 N, TMIN = 906 N B. TMAX = 1075 N, TMIN = 690 N
determine the maximum value of the mass of block b for which the blocks will not move assume that the pulley is frictionless and negligible of mass
Neglect friction of the 55-Ibf collar against its vertical guide and compute the velocity of the collar after it has fallen 7ft., starting from22 ft/sec. in the position shown below. The unstretched length of the spring is 3ft.
: Block B has a mass m and is released from rest when it is on top of cart A, which has a mass of 3kg. Determine the tension in cord CD needed to hold the cart from moving while B slides down A. Neglect friction. =30o
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
Determine the linear impulse of the block at t = 3 seconds.
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
4-kg sphere rests on the smooth parabolic surface.Determine the normal force it exerts on the surface and themass mB of block B needed to hold it in the equilibriumposition shown.