5. In the figure shown below, the height of the water and oil are 15 and 8 m respectively. The container is open to the atmosphere (a) What is the gauge pressure and absolute pressure at the oil water interface? (b) What is the gauge pressure and absolute pressure at the bottom of the container? The density of the oil is 750kg/m^3 OIL WATER shutterstock.com 1172374471

5. In the figure shown below, the height of the water and oil are 15 and 8 m respectively. The container is open to the atmosphere (a) What is the gauge pressure and absolute pressure at the oil water interface? (b) What is the gauge pressure and absolute pressure at the bottom of the container? The density of the oil is 750kg/m^3 OIL WATER shutterstock.com 1172374471

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The tank in Fig is 120 cm long into the paper. Determinethe horizontal and vertical hydrostatic forces on thequarter-circle panel AB . The fl uid is water at 20 ° C. Neglectatmospheric pressure.
A closed tank contains 1.5 m of SAE 30 oil, 1m of water, 20 cm of mercury, and an air pocket in its upper part, all of them at 20 ° C. The absolute pressure at the bottom of the tank is 60 kPa. What is the pressure in the air bag?
[Fluid dynamics] a.) For your science exhibit, you want to make a block of wood float at the interface between a layer of oil of unknown density ?_???, and water (?_????? = 1000 [kg/m^3]) inside a container as shown. What must be the density of the oil so that only 30.0% of the wood is submerged in water? b.) Water is flowing through a pipeline shown onthe right. The radii of the pipe at points 1 and 2 are0.500 [m] and 1.50 [m], respectively. The volume flowrate through the pipeline is 2.50 [L/s]. If the pressureat point 1 in the pipe is 200 [kPa], what is the pressureat point 2, located 5.00 [m] above point 1?
Two small vessels are connected to a U-tube manometercontaining mercury(relative density 13.56) and the connectingtubes are filled with alcohol (relative density 0.82). Thevessel at the higher pressure is 2 m lower in elevation than theother. What is the pressure difference between the vessels whenthe steady difference in level of themercury menisci is 225 mm?What is the difference of piezometric head? If an inverted U-tubemanometer containing a liquid of relative density 0.74 wereused instead, whatwould be the manometer reading for thesame pressure difference?
A volume of 450 cm3 of air is measured at a pressure of 740 mm Hg absolute and atemperature of 20°C. If the pressure and temp changes to 760 mm Hg absolute and 0°C.Determine the final volume in cm3.
Two thin flat plates, tilted at an angle α , are placed in a tankof liquid of known surface tension Y and contact angle θ ,as shown in Fig. C1.3. At the free surface of the liquid inthe tank, the two plates are a distance L apart and havewidth b into the page. The liquid rises a distance h betweenthe plates, as shown.( a ) What is the total upward ( z -directed) force, due to surfacetension, acting on the liquid column between theplates?( b ) If the liquid density is ρ , fi nd an expression for surfacetension Y in terms of the other variables.
An air-filled, hemispherical shell is attached to the ocean floor at adepth of 10 m as shown in fig. A mercury barometer located inside the shell reads 765 mmHg (absolute pressure inside the shell)m, and a mercury u-tube manometer designedto givethe outside water pressure indicates differential reading of 735 mmHg as illusrated. Based on these data,what is the atmospheric pressure at the ocean surface for seawater (SG=1.03)
Capillary rise in the glass tube used for measuring water level isnot to exceed 0.5 mm. Determine its minimum size, given thatsurface tension for water in contact with air = 0.07112 N/m.
The tank in Fig. contains benzene and is pressurizedto 200 kPa (gage) in the air gap. Determine the verticalhydrostatic force on circular-arc section AB and its line ofaction.
What is the pressure at the bottom of 0.5m height fluid if the container moves 5m/s2 upward? Fluid has a density of 2000kg/m3 a. 13665Pab. 13258Pac. 14810Pad. 16145Pa
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
A cylindrical tank of 1.5 m diameter and height 0,75 m has a hemispherical dome. The tank contains oil of relative density 0.84. The dame is joined to cylinder position by four equally spaced bolts. If pressure gauge at point M, 0.3 m above base of tank read 50 kPa. Determine force each bolt.