5. Torque. A square metal plate 0.180 m on each side is pivoted about an axis through point 0 at its center and perpendicular to the plate. Calculate the net torque about this axis due to the three forces shown in the figure if the magnitudes of the forces are F1 = 18.0N, F2 = 26.0N, and F3 = 14.0N. The plate and all forces are in the plane of the page 0.180 m 0.180 m 45⁰ F3

5. Torque. A square metal plate 0.180 m on each side is pivoted about an axis through point 0 at its center and perpendicular to the plate. Calculate the net torque about this axis due to the three forces shown in the figure if the magnitudes of the forces are F1 = 18.0N, F2 = 26.0N, and F3 = 14.0N. The plate and all forces are in the plane of the page 0.180 m 0.180 m 45⁰ F3

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Dynamics

Section: Chapter Questions

Problem 6CQ: A person stands a distance R from a doors hinges and pushes with a force F directed perpendicular to...

See similar textbooks

Similar questions

What are the necessary conditions for equilibrium of the object shown in Figure P12.1? Calculate torques about an axis through point O.
(a) Give an example in which the net force acting on an object is zero, yet the net torque is nonzero, (b) Give an example in which the net torque acting on an object is zero, yet the net force is nonzero.
(a) When opening a door, you push on it perpendicularly with a force of 55.0 N at a distance of 0.850m from the hinges. What torque are you exerting relative to the hinges? (b) Does it matter if you push at the same height as the hinges?
What three factors affect the torque created by a force relative to a specific pivot point?
A person stands a distance R from a doors hinges and pushes with a force F directed perpendicular to its surface. By what factor does the applied torque change if the persons position and force change to (a) 2R and 2F, (b) 2R and F, (c) R and F/2, (d) R/2 and F/2?
In analyzing the equilibrium of a flat, rigid object, you are about to choose an axis about which you will calculate torques. Which of the following describes the choice you should make? (a) The axis should pass through the objects center of mass. (b) The axis should pass through one end of the object. (c) The axis should be either the x axis or the y axis. (d) The axis should pass through any point within the object. (e) Any axis within or outside the object can be chosen.
The fishing pole in Figure P10.22 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F=100N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 m from the anglers hands. Figure P10.22
A simple pendulum consists of a small object of mass 3.0 kg hanging at the end of a 2.0-m-long light string that is connected to a pivot point. (a) Calculate the magnitude of the torque (due to the force of gravity) about this pivot point when the string makes a 5.0 angle with the vertical. (b) Does the torque increase or decrease as the angle increases? Explain. Figure P8.6
An automobile engine can produce 200 N m of torque. Calculate the angular acceleration produced if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0 kg disk that has a 0.180 m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
A rigid body is rotating counterclockwise about a fixed axis. Each of the following pairs of quantities represents an initial angular position and a final angular position of the rigid body. Which of the sets can occur only if the rigid body rotates through more than 180? (a) 3 rad, 6 rad; (b) 1 rad, 1 rad; (c) 1 rad, 5 rad.
The fishing pole in Figure P10.28 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F = 100 N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 in from the anglers hands.
Suppose you exert a force of 180 N tangential to a 0.280-m-radius 75.0-kg grindstone (a solid disk). (a)What torque is exerted? (b) What is the angular acceleration assuming negligible opposing friction? (c) What is the angular acceleration if there is an opposing frictional force of 20.0 N exerted 1.50 cm from the axis?