5.98 Two C12 x 20.7 channels are joined to 8.5-in. by 0.5-in. plates with 3/4-in. rivets to form a beam with the cross section shown in the figure. The maximum shear force in the beam is 20 kips. (a) Determine the maximum allowable spacing of the rivets using 5000 psi for the working shear stress. (b) Compute the corresponding maximum bearing stress in the channels.

5.98 Two C12 x 20.7 channels are joined to 8.5-in. by 0.5-in. plates with 3/4-in. rivets to form a beam with the cross section shown in the figure. The maximum shear force in the beam is 20 kips. (a) Determine the maximum allowable spacing of the rivets using 5000 psi for the working shear stress. (b) Compute the corresponding maximum bearing stress in the channels.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P (kN)= 7 allow=45 Pin C=double shear Pin D=single shear
Refer to the illustration below. ?′?=28 MPa, ??= 400 MPa. Answer all subparts: a. Determine the ultimate axial capacity of the spiral column b. Determine the maximum spiral pitch c. Determine the clear spacing between the main reinforcements
Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine thefollowing: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle baris 60 MPa. Thickness of angle bar B is 6 mm.b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is25 MPa. Thickness of angle bar is 5 mm.
Calculate the stresses in members AB, DF, and BD. Given:FAB = 51.22 kN (C)FDF = 50 kN (C)FBD = 32.98 kN (C)d = 0.05 m
If w=30 kN/m and L=10m, the cross section is made-up of two l-beams shows, determine the following a. Maximum bending stress b. Spacing of the bolts
A spiral column carries a dead load of 1070 kN and a live load of 980 kN. Iff’c = 27.50 MPa, fy = 413.50 MPa, using a steel ratio of 3%a. Compute for the value of the diameter of spiral columnb. Compute the number of 28 mm ø main reinforcement. c. Compute for the possible spacing of 10 mm ø spirald. Sketch the col
4. If the width of the bedplate is 3m and the clearance is 0.3 what is the upper width of the machine foundation
A 16 ??–diameter steel rod AB is fitted to a round hole near end C of the wooden member CD. For the loading shown, determine, (a) the distance b for which the average shearing stress is 7??? on the surfaces indicated by the dashed lines, (provide FBD and answer in ??)(b) the average bearing stress on the wood (provide FBD and answer in ???)
Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine the following: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle bar is 60 MPa. Thickness of angle bar B is 6 mm. b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is 25 MPa. Thickness of angle bar is 5 mm.
Let the allowable stresses in the post be ??? = 120 ??? and ??? = 6 ???. Compute the maximum safe axial load P that may be applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Each steel bar has cross-sectional area of 900??2
Determine the internal force system acting on section 1 by analyzing the FBA of a) segment AD and b) segment DB
Check if it is safe for A) one way shear B) two way shear