53. An 8.00-L sample of gas at 99.0 kPa and 25 deg C is compressed. What is its final pressure at 25 deg C if the gas is compressed 2.00 L? A. 396 kPa B. 369 kPa O132 kPa D 123 LRa

Q: Find the particular solution of this differential equation, and plot the result.

A:

Q: Determine the constraint equation which relates the accelerations of bodies A and B. Assume that the...

A:

Q: for distance s 54 1-17t from time 0.1 to 2 seconds, determine the maximum velocity.

A: To find maximum velocity

Q: 40 kN 15 kN 3. Two forces are acting on a beam as shown. L30 Determine a single resultant force and ...

A:

Q: 1- A well-insulated rigid tank contains 2 kg of a saturated liquid-vapor mixture of water at 100 kPa...

A: Answer: The entropy change of the steam during this process is 8.1 kJ/K.

Q: A single acting compressor with a 15cm bore and 18cm stroke operates at 350rpm. The clearance is 5% ...

A:

Q: 10. What are the component of pressure loss of drilling fluids flow for a well drilling? What's the ...

A: Since we only answer one question at once, we will solve the first. Please resubmit the other questi...

Q: 134 Calculate the angular acceleration of the plate in the position shown, where control link AO has...

A: To given that,Angular velocity=ωOA=4rad/secθ=60°we know thatVA=VB=rwLinear velocity(v)=angular veloc...

Q: What is the center type of this valve?

A: See the answer in the next page.

Q: Given the following Product Structure Record, the number of D's required for each A is A B(3) C(2) D...

A: Given Data: Number of B required for each A, 3 Number of C required for each A, 2

Q: Bhāskara's wheel:Discuss the system of a perprtual machine in the context of the first and second l...

A:

Q: Based from the rectangular framework below, a. solve for the summation of the moments of force about...

A: Given data, Applied force, K = 23 lbs To determine:- a) Summation of moment of force about pivot M b...

Q: The power plant operates on a Rankine cycle. Operating pressure from 2000 psia to 1 psia. The temper...

A:

Q: 12 kg/s of steam expands in an adiabatic turbine from at 10 MPa and 450°C to 10 KPa. The inlet and e...

A:

Q: EX1- It is required to pump water out of deep well under a total head of 90 m. A number of identical...

A: Total head, H= 90 m Design speed, N= 1000 rpm Specific speed, NS= 30 Rated capacity, Q= 0.15 m3/s   ...

Q: Calculate the modulus of elasticity of the following material if it has a design stress of 250 kPa, ...

A:

Q: For the following mechanism, if the length of rod AO, I = 1.6 m, and its angular velocity W = 7.1 ra...

A:

Q: 12 cm x 16 cm air compressor is operated with a maximum pressure of 10 kg/cm^2. There are 5 bolts wi...

A:

Q: 6. Find the reaction forces at point A and B 20 lb 30 lb/ft A B 10' 10'

A:

Q: For the T-shaped device shown in the figure, 3 couples act and a force S = 71i+30j- 15k If M= 60lb, ...

A:

Q: Two airplanes are performing at an air show. Plane A travels along the path shown and, for the insta...

A:

Q: In Figure below, a cantilever beam is subjected to an inclined force (P); calculate: 1- The normal s...

A: Answer: 1. The normal stress is 144.3375 kPa. 2. The shear stress is 83.3333 kPa.  

Q: Q= 200 L/s Z2 =10m 71 =5m Datum

A: Given Data Q=200 l/s=0.2 m3/s Z1=5 m Z2=10 m V2=4 m/s

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4250 mm2 and an...

A:

Q: The velocity of a particle traveling along a straight line is v= (312 - 6t) ft/s, where t is in seco...

A: Given: Velocity of the particle→v=312-6t  fts We know that→v=dsdt Hence: →dsdt=312-6t→ds=312-6tdt→∫d...

Q: An oil of specific gravity 0.77 and viscosity 0.05 poise is flowing through a pipe of diameter 240m...

A: GIVEN DATA- DENSITY =770 kg/m3 viscosity 0.05 poise = 0.005 Ns/m2 diameter=240mm Flow rate=50 lit/s ...

Q: A force, F = 12 N, making an angle of 02 = 15° to the ramp pulls up a block of mass m = 2 kg. The ra...

A: (a) The acceleration of the block up the ramp when the length of the spring is 0.6 m is 0.4 m/s2. (b...

Q: A square plate 0.5m x 0.5m weighing 100N is allowed to slide down an inclined plane which is laid to...

A: GivenA=0.5m ×0.5mW=100Nt=0.03mmμ=2×10-3 Ns /m2

Q: For the beam shown below, Find the bending stress at point A. 16 50 kN 22 + 3 m 3 m

A:

Q: Determine the generated moment about point O. 600 lb 20°[ 0.5 ft

A:

Q: 10.Calculate the volumetric flow through nozzle meter if; Nozzle flow coefficient (a) and Nozzle Exp...

A:

Q: -3 m end is tied to a steel cable of length 3.00 m, as shown in the figure. The other end of the cab...

A:

Q: by Velocity and Acceleration Analysis. Also show the velocity and acceleration polygons

A:

Q: The solid circular rod has a cross-sectional area of 310 mm2. It is subjected to a uniform axial dis...

A:

Q: As an oil well is drilled, each new section of drill pipe supports its own weight and that of the pi...

A:

Q: Find the minimum principal stress if maximum shear stress is 10 MPa and maximum principal stress is ...

A: Given data : Maximum shear stress=ζMaxMaximum principal stress=σ1To find :Minimum principal stress

Q: A yoke, alternatively known as a control wheel or a control column, is a device used for piloting so...

A: Answer: velocity of wind ,v w =21 mil/hr Relative velocity of plane,va/w=78 mil/ hr Drawing the vel...

Q: robotic arm

A: INTRODUCTION ROBOTIC ARM-:A Robotic  arm is a form of mechanical arm, generally programmable, with c...

Q: In the 1950’s an experimental train that had a mass of 25,000 kg was powered across a level 500 m tr...

A:

Q: (5) A rectangular bar is cut from an AISI 1018 cold-drawn steel flat. The bar is 60 mm wide by 10 mm...

A:

Q: A heat exchanger is incorporated into an ideal air-standard refrigeration cycle, as shown in figure....

A:

Q: د.ضمياء( H.w 1-ch.5 Q1/ A large vertical plate 6.1 m high and 1.22 m wide is maintained at a constan...

A:

Q: A 10-kg body is pulled upward with an acceleration of 0.40 m/s. Calculate the tension in the cord.

A: Mass (m) = 10 kg Acceleration (a) = 0.4 m/s2 Therefore, we can find tension with the force equation....

Q: In CNC manufacturing chain, CL-data is generated post processor. O before after O None of above

A: CNC is a computer numerical control machine that uses G Codes and M codes for the machining of compo...

Q: for distance s= 54 - 17t from time 0.1 to 2 seconds, determine the maximum velocity.

A:

Q: Air enters a nozzle at 0.2 MPa, 350 K, and a stagnation velocity. Assuming isentropic flow, determin...

A:

Q: A 50 mm by 100 mm timber is used as a columns with fixed ends. Determine the minimum length at which...

A: Given:Timber dimension=50 mm×100 mmE=10 GpaProportional limit=30 MPa2nd part,Length, l=2.5 mFoS=2

Q: A small ship capable of making a speed of 5.8 knots through still water maintains a heading due east...

A: Answer: (a) The speed of the current is 1.6175 knots. (b) It's direction measured clockwise from Nor...

Q: Motion of the sliding block P in the rotating radial slot is controlled by the power screw as shown....

A:

Q: The bronze C86100 pipe has an outer diameter of 1.875 in. and a thickness of 0.125 in. The coupling ...

A: Answer: The maximum shear stress in the pipe is 283.64 psi.  

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.