The bronze C86100 pipe has an outer diameter of 1.875 in. and a thickness of 0.125 in. The coupling on it at C is being tightened using a wrench. The applied force is F = 24 lb.A10 in.6 in.Sin6 inPart ADetermine the maximum shear stress in the pipe.Express your answer to three significant figures and include appropriate units.HA?ValueUnitsTmax =

Answer: The maximum shear stress in the pipe is 283.64 psi.

The bronze C86100 pipe has an outer diameter of 1.875 in. and a thickness of 0.125 in. The coupling on it at C is being tightened using a wrench. The applied force is F = 24 lb. 10 in X6 in S in 6 in. Part A Determine the maximum shear stress in the pipe. Express your answer to three significant figures and include appropriate units. HÀ ? Tmax = Value Units

The bronze C86100 pipe has an outer diameter of 1.875 in. and a thickness of 0.125 in. The coupling on it at C is being tightened using a wrench. The applied force is F = 24 lb. 10 in X6 in S in 6 in. Part A Determine the maximum shear stress in the pipe. Express your answer to three significant figures and include appropriate units. HÀ ? Tmax = Value Units

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy = 250 MPa. Determine the safety factor at point A using the maximum shear stress theory. Select one: a. NA = 1.843 b. NA = 3.224 c. NA = 2.580 d. NA = 4.299
The five-bolt connection must support an applied load of P = 3500 lb. If the average shear stress in the bolts must be limited to 29 ksi, determine the minimum bolt diameter that may be used for this connection.
The shaft is used to transmit 30 hp while turning at 600 rpm. Determine the maximum shear stress in the shaft. The segments are connected together using a fillet weld having a radius of 0.18 in.
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
The A-36 steel tubular shaft is 2 m long and has an outer diameter of 50 mm. When it is rotating at 40 rad>s, it transmits 25 kW of power from the motor M to the pump P. Determine the smallest thickness of the tube if the allowable shear stress is tallow = 80 MPa.
Two A992 steel pipes, each having a cross-sectional area of 0.32 in2, are screwed together using a union at B. Originally the assembly is adjusted so that no load is on the pipe. If the union is then tightened so that its screw, having a lead of 0.15 in., undergoes two full turns, determine the average normal stress developed in the pipe. Assume that the union and couplings at A and C are rigid. Neglect the size of the union. Note: The lead would cause the pipe, when unloaded, to shorten 0.15 in. when the union is rotated one revolution.
A torque of 2 kip # in. is applied to the tube. If the wall thickness is 0.1 in., determine the average shear stress in the tube.
The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4x103 ksi and G brass at 5.2 x 103 ksi. complete soln.
The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. Select one: a. NH = 6.427 b. NH = 3.570 c. NH = 5.355 d. NH = 4.590
The 6061-T6 aluminum bar has a square cross section of 25 mm by 25 mm. If it is 2 m long, determine the maximum shear stress in the bar and the rotation of one end relative to the other end.
Determine the maximum normal stress in the bar. The diameter is 1.5cm.F1 = 7KN F2 = 6KN F3 = 2KN F1 = 9KN
The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (sb)allow = 2 ksi, and the allowable tensile stress within the bolt shank S is (st)allow = 18 ksi, determine the maximum allowable tension in the bolt shank. The bolt shankhas a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.