5m/s k-40KN/m ww 1 т— The box with a mass of 8 kg shown in the figure slides on a surface with a kinetic friction coefficient of 0.3. The speed of the box when is 1 m away from the plate is v = 5 m / s. The box hits the 4 kg plate. Since the spring coefficient is 40 kN / m, determine the maximum shortening of the spring. Take the return coefficient e = 0.8 between the box and the plate. %3D

5m/s k-40KN/m ww 1 т— The box with a mass of 8 kg shown in the figure slides on a surface with a kinetic friction coefficient of 0.3. The speed of the box when is 1 m away from the plate is v = 5 m / s. The box hits the 4 kg plate. Since the spring coefficient is 40 kN / m, determine the maximum shortening of the spring. Take the return coefficient e = 0.8 between the box and the plate. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An 8 kg and a 2 kg block are attached to a pulley system as shown in the picture and a force is being applied to the left. If the 2 kg block is accelerating upward at 1.2 m/s2 , what is the force used to pull the blocks? There is no friction between the 8 kg block and the surface its moving across and you can assume the rope is massless and the pulley is massless and frictionless. a) 78.4 N b) 19.6 N c) 31.6 N d) 98.0 N
A 119.23-kg skier starts with an initial speed of 29.22 m/s and coasts up a H=6.10-m-high rise as shown in the figure. If her final speed at the top is 14.35 m/s, what is the angle of the slope in unit of degrees? Assume the coefficient of friction between her skis and the snow is 0.10 (Hint: Find the distance traveled up the incline assuming a straight-line path as shown in the figure.) Use g = 10 m/s2.
To be able to use the conservation of energy on a moving body to determine key characteristics about the mechanics of the system. A package of mass m= 1.00 kg is pushed across the surface by a jet of compressed air during an assembly-line process. The package is moved through a distance of s = 47.0 cm. The package and the surface are known to have a coefficient of kinetic friction of μk= 0.15. The package is initially at rest for this process. If the package must be moving at a speed of v = 17.0 cm/s when it has reached the distance of 47.0 cm, determine the average force that the jet of compressed air must supply to the package If it is now desired that the package be at rest when it has reached the distance of 47.0 cm , determine the average force that the jet of compressed air must supply to the package if the package is initially traveling in the s direction at a velocity of v = 13.5 cm/s If the plant has changed the mass of the package on the assembly line to m = 1.35 kg ,…
Block A of 500-kg mass is subjected to a towing force F= 2000 t^2 + 3000 t N where "t" is in seconds. If the initial velocity of the block is 6 m/s, determine the velocity after 4 seconds. The block is being towed at a surface inclined at 45 degrees and the coefficient of kinetic friction between these is 0.2. Answer: 106.04 m/s Show COMPLETE STEP-BY-STEP SOLUTIONS and NECESSARY FIGURES to satisfy the answer. Thank you
The figure shows a junction of mass m = 10kg sliding on a rod in a vertical plane. Positioned 1 simpai is stationary and horizontal spring and tensioned Fp = 300N. If the spring constant is k = 1kN/m and the average frictional force between the rod and the junction is F = 30N. Calculate the speed at position 2. (Ans: 3.47m/s)
A car travelling in a constant velocity wants to turn in a 10m radius flat curve. If the coefficients of static and dynamic friction are 0.4 and 0.2, respectively, determine the car's velocity in kph.
What work is done on a level track in bringing the velocity of a train weighing 200 tons from zero to 30 mi/hr, if the frictional resistance at any velocity is 12 lb/ton, and if the change in speed is accomplished in a length 5280 ft? If the track were a 1% upgrade, what would be the additional work to be done?
A belt conveyor is required to deliver crushed limestone having a bulk density of 50 lb/ft3 at the rate of 100 tons/hr. The conveyor is to be 100 ft. between pulleys with a rise of 25 ft. with a belt speed of 100 ft/min. Determine the ff: a. The minimum width of belt b. The horsepower required to drive the motor if its efficiency is 90%
A speedboat with a mass of 529 kg (including the driver) is tethered to a fixed buoy by a strong 28.3 m cable. The boat's owner loves high speed, but does not really want to go anywhere. So the owner revs up the boat's engine, makes a lot of noise, and runs the boat in circles around the buoy with the cable supplying all the necessary centripetal force. When the tension of the cable is steady at 12300 N, with what force is the boat's engine pushing the boat? Different physics textbooks treat drag force somewhat differently and use different formulas. For the present purpose, take the water's drag force on the boat to be (450 kg/m)×v2, where v denotes the boat's speed. Ignore any drag force on the cable. What is the force of the engine?
1.An 8.70-kg block slides with an initial speed of 1.56 m/s up a ramp inclined at an angle of 28.4° with the horizontal. The coefficient of kinetic friction between the block and the ramp is 0.62. Use energy conservation to find the distance the block slides before coming to rest. Explain and draws.
In the given figure below, a 3.0 -kg block is sliding down a 60o-rough incline. The speed of the block is 1.68 m/s at the instant it is 5.25 m from an uncompressed spring located at the other lower end of the incline. The spring has a spring or stiffness constant of 120 N/m and the coefficient of kinetic friction between the block and the incline is 0.35. (a) At what speed (in m/s) will the block strike the spring? (b) What would be the maximum compression (in m) of the spring?
An industrial trolley of mass 300 kg is used to transport equipment and materials to a workstation within the R and D section. Initially the trolley is at the top of a 15 m high hill, which is inclined at 10º to horizontal as shown and travelling at 5 m/s before rolling down into the station. On reaching the bottom of the hill, brakes are applied to the trolley to slow it down to 0.25 m/s in 4.5 m. Determine: The braking force that slowed the trolley down The time it takes the trolley to slow down The deceleration of the trolley