Point mass starts to slide down from a point A on a rough inclined plane having a coefficient of friction u with zero initial velocity and enters the frictionless circular track shown in the figure. Find the height h that the mass should start to move (from point A) in order to be able to remain on the track at point B. rough h ( r- 40 cm, μ = 0.4, α = 450 ) smooth

Point mass starts to slide down from a point A on a rough inclined plane having a coefficient of friction u with zero initial velocity and enters the frictionless circular track shown in the figure. Find the height h that the mass should start to move (from point A) in order to be able to remain on the track at point B. rough h ( r- 40 cm, μ = 0.4, α = 450 ) smooth

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 24 kg box is being pushed across the floor by a constant force <111, 0, 0> N. The coefficient of kinetic friction for the table and box is 0.18. At t= 8 s the box is at location <16, 5, -6> m, traveling with velocity <3, 0, 0> m/s. What is its position and velocity at t= 9.2 s? What is the new velocity and new position?
Q6) A water jet hits horizontally a 50-kg block with a velocity of (20 m/s), see the figure. The friction coefficient between the block and the ground is (0.9). What is the minimum diameter (d) of the water jet required for the block to slide to the left?
A wheel tractor has a 200HP engine.If the weight of the wheel tractor is 30 tons and the weight on the drivingwheels is 50% of this weight, and it is operating at an altitute of 1000m above sea level, at an average temperature of 25 degree celcius, and at an average speed of 12km/hr. What is the maximum available rimpull if thecoefficient of traction is 0.25?. Take rimpull efficiency as 85%
The super-container vessel in the figure has a total mass displacement of (4000) long tons. This vessel towed by a tugboat with α=20⁰ angle with horizontal. If a constant tension is applied as F= 400 kN by the tugboat, please calculate the time to bring the vessel to a speed of 2 knot from the rest. At these low speeds, please neglect the hull resistance that created by the motion. Note: (1 long tons = 1016.05 kg, 1 knot=1.151 mi/hr= 0.5144 m/s)
A horizontal water jet with a 2.5 cm diameter and a speed of V =40 m/s relative to the ground is deflected by a 60° stationary cone whose base di ameter is 25 cm The height of water along the cone is 0.125cm. Disregarding the effect of gravity and the shear forces, the horizontal force F needed to hold the cone stationary is
Consider two different flows over geometrically similar airfoil shapes,one airfoil being twice the size of the other. The flow over the smallerairfoil has freestream properties given by T∞ = 200 K, ρ∞ = 1.23 kg/m3,and V∞ = 100 m/s. The flow over the larger airfoil is described byT∞ = 800 K, ρ∞ = 1.739 kg/m3, and V∞ = 200 m/s. Assume thatboth μ and a are proportional to T 1/2. Are the two flows dynamicallysimilar?
The Cessna Citation executive jet weighs 67 kN and has awing area of 32 m2. It cruises at 10 km standard altitudewith a lift coeffi cient of 0.21 and a drag coeffi cient of0.015. Estimate (a) the cruise speed in mi/h and (b) thehorsepower required to maintain cruise velocity.
A rotating dishwasher arm delivers at 60 ° C to six nozzles,as in Fig.. The total fl ow rate is 3.0 gal/min. Eachnozzle has a diameter of 3/16 in. If the nozzle fl ows are equaland friction is neglected, estimate the steady rotation rateof the arm, in r/min.
A 3-in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which deflects the water 180 degrees at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream. Please no conversion need it, only the 3in into .25feet, please. for me, I got 3.71KN on the x-axis.
An 16-kg slab slides down a 25° inclined plane on a 4-mmthick film of SAE 30 oil at 15.6 °C; the contact area is0.3m2. Find the terminal velocity of the slab. Explain ur answer
A lawn sprinkler with three identical arms is used to water a garden by rotating in a horizontal plane by the impulse caused by water flow. Water enters the sprinkler along the axis of rotation at a rate of 45 L/s and leaves the 1.5-cm-diameter nozzles in the tangential direction. The bearing applies a retarding torque of T0 = 40 N·m due to friction at the anticipated operating speeds. For a normal distance of 40 cm between the axis of rotation and the center of the nozzles, determine the angular velocity of the sprinkler shaft.
1. Assuming that there are no heat effects and no frictional effects,find the kinetic energy and speed of a 3220lb body after it falls 778 ft from rest. Start with the steady flow equation, deleting energy terms which are irrelevant. Draw a figure or FBD that will support the problem. Explain each step by step formula.