Water (p= 1000 kg/m³) strikes a block as shown and is deflected 30°. The flow rate of the water is 1.5 kg/s, and the inlet velocity is V = 10m/s .The mass of the block is 1 kg. The coefficient of static friction between the block and the surface is 0.1 (friction force normal force). If the force parallel to the surface exceeds the frictional force, the block will move. Determine the force on the block and whether the block will move. Neglect the weight of the water. Vertical Block 30°

Water (p= 1000 kg/m³) strikes a block as shown and is deflected 30°. The flow rate of the water is 1.5 kg/s, and the inlet velocity is V = 10m/s .The mass of the block is 1 kg. The coefficient of static friction between the block and the surface is 0.1 (friction force normal force). If the force parallel to the surface exceeds the frictional force, the block will move. Determine the force on the block and whether the block will move. Neglect the weight of the water. Vertical Block 30°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hydroelectric power plant uses Pelton-type turbines, in which multiple nozzles are used to accelerate the waterwhich is directed onto the turbine blades, which are exposed to an atmospheric pressure of 101.325 kPa. The water enters the nozzles with an absolute pressure of 500 kPa and a speed of 5 m/s, and the nozzle outlets are exposed to atmospheric pressure and have an internal diameter of 5 cm. Consider that the specific mass of water is 1,000 kg/m3. Determine the mass flow rate of water through each of the nozzles, and explain why the actual mass flow rate will be lower.
A lawn sprinkler with three identical arms is used to water a garden by rotating in a horizontal plane by the impulse caused by water flow. Water enters the sprinkler along the axis of rotation at a rate of 45 L/s and leaves the 1.5-cm-diameter nozzles in the tangential direction. The bearing applies a retarding torque of T0 = 40 N·m due to friction at the anticipated operating speeds. For a normal distance of 40 cm between the axis of rotation and the center of the nozzles, determine the angular velocity of the sprinkler shaft.
A 16-cm diameter horizontal water jet with a speed of Vj = 20 m/s relative to the ground is deflected by a 40° cone moving to the left at Vc = 10 m/s. Determine the external force, F, needed to maintain the motion of the cone. Disregard the gravity and surface shear effects and assume the crosssectional area of water jet normal to the direction of motion remains constant throughout the flow.
A reducing elbow is used to deflect water flow at 25 L/s in a horizontal pipe upward by an angle of=45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow is 15 cm at the inlet and 5 cm at the exit. The elevation difference between the center of the exit and inlet is 40 cm. The mass of the elbow and the water in it is 40 kg. Determine the anchoring force needed to hold the elbow in place, assuming a momentum-flux correction factor of 1.03.
A fan running at 1480 rpm takes in 6 m^3/min of air at inlet conditions of P_1=950 mbar and T_1=15^0 C. If the fan impeller dimeter is 40 cm and the table tip air angle 20^0, determine the total pressure developed by the fan and the impeller width at exit. Take the radial velocity at the exit as 0.2 times the impeller tip speed. State the assumptions used.
The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disre- garding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volu- metric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
Calculate the velocity values in the D and E sections of the system in the figure. AE/AD= 3, Z1=1.6 m and Z2=0.2 m. The mercury deviation in the manometer is Z3=0.4 m. (Friction effects will be neglected, γmercury=13.6 t/m3 , γwater=1 t/m3).
A U-tube acts like a water siphon. The elbow in the tube is 1 m above the water surface, the tube outlet is L from point A below. When the length L is 5 m, the water emerges from the bottom of the siphon as free jet at atmospheric pressure. Determine the speed of the free jet and the minimum absolute pressure of the water at the elbow. (Patm= 101325 Pa, dsu=1000 kg/m3)
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
Air flows steadily from a tank pressurized to 3kPa through a pipe of diameter D = 0.03 m and finally discharges to the atmosphere through a nozzle of diameter 0.01m. If the specific weight of air is 12 N/m^3 the air flow rate is?
A jet of water, issuing from sharp-edged vertical orifice under a constant head of 60 cm , has the horizontal and vertical coordinates measured from vena contracta at a certain point as 10. cm and 0.45 cm respevtively. Find Cc if Cd= 0.60.include your free body diagrama.0.612 b.0.962 c.0.98 d.0.623
A 30° elbow is used to deflect water flow at a rate of 14 kg/s in a horizontal pipe upward The elbow discharges water into the atmosphere Cross-sectional areas of the elbow are 113 cm^2 at the inlet and 7 cm^2 at the outlet. The elevation difference between the centers of the outlet and the inlet is 30 cm Neglect the weight of the elbow and the water inside the elbow,Using appropriate integral equations, find a) Wet and outset velocity b) Gage pressure at the center of the inlet section of the elbow c) Anchoring force required to hold the elbow In place Take the density of water to be 1000kg/m^3 & the flow is incompressible.