5x5 in. Wooden beams and steel plates are securely bolted together to form the composite member shown. Using the data given below, determine the largest permissible bending moment when the member is bent about a horizontal axis. 10 in. Wood Steel Modulus of elasticity: 2 x10° psi 29x10 psi in. 6 in Allowable stress: 2000 psi 22 ksi

5x5 in. Wooden beams and steel plates are securely bolted together to form the composite member shown. Using the data given below, determine the largest permissible bending moment when the member is bent about a horizontal axis. 10 in. Wood Steel Modulus of elasticity: 2 x10° psi 29x10 psi in. 6 in Allowable stress: 2000 psi 22 ksi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross section (assume that the h/b ratio is 2) and is made of wood (E = 11GPa). Find height h of the cross section if the maximum displacement of the beam is 2 mm. Calculate the displacement of the beam at the inflection points.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.
Copper beam AB has circular cross section with a radius of 0.25 in. and length L = 3 ft. The beam is subjected to a uniformly distributed load w = 3.5 lb/ft. Calculate the required load P at joint B so that the total deflection at joint B is zero. Assume that£ = 16,000 ksi.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
‘11.5-2 A steel bar having a square cross section (50 mm × 50 mm)and length L = 2.0 in is compressed by axial loads that have a resultant P = 60 kN acting at the midpoint of one side of the cross section (sec figure). Assuming that the modulus of elasticity £is equal to 210 GPa and that the ends of the bar are pinned, calculate the maximum deflection S and the maximum bending moment Mmax.
Wooden beams and steel plates are securely bolted together to form the composite member shown. Using the data given below, determine the largest permissible bending moment when the compos-ite member is bent about a horizontal axis.Modulus of elasticity 2 * 106 psi 29 * 106 psi Allowable stress 2000 psi 22 ksi
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis.Modulus of elasticity 70 GPa,105 GPa Allowable stress100 MPa,160 MPa
QUESTION 2 A rectangular strip of metal 5 mm thick is wound on a circular drum 1.4 m in diameter. If E for the metal is 120 GPa, 2.1 Calculate the maximum bending stress induced in the strip.
A bar obtained by bonding together pieces of steel (Es= 29 * 106 psi) and brass (Eb= 15 * 106 psi) has the cross section shown (Fig. ). Determine the maximum stress in the steel and in the brass when the bar is in pure bending with a bending moment M= 40 kip?in.
Applying the flexure formula, how can we determine the position of the absolute maximum bending stress that occur?
A circular solid cross-section cantilever is fixed at one end and bears a concentrated load P at the other. Over a 2m length, the diameter increases uniformly from 200 mm at the free end to 400 mm at the fixed end. At what distance from the free end will the bending stress in the cantilever be maximum? If the concentrated load P=30 KN, what is the maximum bending stress