A simply supported timber beam with length L = 4 m carries a uniformly distributed load w = 12 kN/m. Determine the magnitude of the maximum compression bending stress that occurs in the beam at any location within the 4-m span length. 300 mm В L 100 mm O 14.92 MPa О 16.00 МPа O 20.78 MPa O 19.09 MPa O 9.62 MPa

A simply supported timber beam with length L = 4 m carries a uniformly distributed load w = 12 kN/m. Determine the magnitude of the maximum compression bending stress that occurs in the beam at any location within the 4-m span length. 300 mm В L 100 mm O 14.92 MPa О 16.00 МPа O 20.78 MPa O 19.09 MPa O 9.62 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.8.1P: A simple beam with a W 10 x 30 wide-flange cross section supports a uniform load of intensity q =...

See similar textbooks

Similar questions

A simple beam with a W 10 x 30 wide-flange cross section supports a uniform load of intensity q = 3.0 kips/ft on a span of length L = 12 ft (sec figure). The dimensions of the cross section are q = 10.5 in., b = 5.81 in., t1= 0.510 in., and fw = 0.300 in. Calculate the maximum shear stress tjuly on cross section A—A located at distance d = 2.5 ft from the end of the beam. Calculate the shear stress rat point Bon the cross section. Point B is located at a distance a = 1.5 in. from the edge of the lower flange.
A frame ABCD is constructed of steel wide-flange members (W8 x 21; E = 30 x ID6 psi) and subjected to triangularly distributed loads of maximum intensity q0acting along the vertical members (see figure). The distance between supports is L = 20 ft and the height of the frame is h = 4 ft. The members are rigidly connected at B and C. Calculate the intensity of load q0 required to produce a maximum bending moment of 80 kip-in. in the horizontal member BC. If the load q0 is reduced to one-half of the value calculated in part (a), what is the maximum bending moment in member BC? What is the ratio of this moment to the moment of 80 kip-in. in part (a)?
.10 A built-up bourn supporting a condominium balcony is made up of a structural T (one half of a W 200 x 31.3) for the top flange and web and two angles (2 L 2 / b / 6.4. long legal back-lo-backl lot the bottom flange and web. as shown. The beam is subjected to a bending moment .1/ having its vector at an angle ft lo the z axis (see figure). Determine the or ion ta I ion of the neutral axis and calculate the maximum tensile stress ir, and maximum compressive stress tr. in ".he beam. .Assume that 9 = 30°andM = 15 kN · m. Use the numerical properties: c =4.111mm, c2 =4.169 mm, of = 134 mm, I, = 76 mm, A = 4144 mm 3 =3.88 X 106 mm 4, and = 34.18 X 10 mm 4.
.20 Determine the plastic moment Mpfor beam having the cross section shown in the figure ey=210 MPa.
A wood box beam is constructed of two 260 mm × 50 mm boards and two 260 mm × 25 mm boards (sec figure). The boards are nailed at a longitudinal spacing. b = 100 mm. If each nail has an allowable shear force F = 1200 N. what is the maximum allowable shear force Vmax?
Determine the ratios of the weights of four beams that have same length.are made of the same material,are subjected to the same lmaximum bending moment,and have the same maximum bending stress if their cross sections are (I) a rectangle with height equal to twice the width,(2) a square,(3) a circle , and (4) a pipe with outer diameter d and wall thickmess f = di% (see figures).
A beam having a T shaped section is subjected to a vertical shear force of V = 10,000 N. The cross sectional dimensions are flange width, bf = 100mm, flange thickness tf = 25mm, gross depth of h = 200 mm and web thickness of 25 mm. Determine the maximum shear stress in the flange.
A beam of rectangular section of 12 cm × 20 cm is simply supported over a span of 12 m. It is acted upon by a load of 80 kN at the mid span. Determine the maximum bending stress induced in thr beam.
Draw the shear and bending moment diagram for the beam.And also show Maximum bending moment Mb=25875lb .ft a tx=9.0ft
A simply supported beam AB = 9 m has a hollow rectangular cross-section with 13 cm as width, 20 cm as depth and inner thickness as 1 cm is subjected to a point load of 8 N & 8 N acting at C and D respectively and a uniformly distributed load (UDL) of 9 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 2 m. note sole 4.5.6.and 7 i) Reaction force at B in (N)= ii) Reaction Force at A in(N)= iii) The distance from B at which the shear Force value changes from "-" to "+" in (m)= iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I in (m^4)= vi) Maximum bending stress in (N/m^2)= vii) Bending stress at 1 cm from the top in (N/m^2) =
An I section symmetrical beamhas 200mm wide flange and overall depth of 500mm. Each flange is 25mm thickand the web is 20mm thick. Determine the maximum bending moment that should be imposed in the sectionif the tensile or the compressive stressis not to exceed 40MN/m^2 and what percentage of the moment is resisted by flange or web?
A simply supported beam AB = 11 m has a hollow rectangular cross-section with 13 cm as width, 22 cm as depth and inner thickness as 2 cm is subjected to a point load of 9 N & 6 N acting at C and D respectively and a uniformly distributed load (UDL) of 9 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 1 m & CD = 1 m. iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =