6 CHEMICAL SUB Sectors *Basic/Commodity Chemicals *Speciality Chemicals *Fine Chemicals *Pharmaceutical *Consumer products *Agricultural Chemicals One Of the six subsectors listed above, choose 2 chemical sub sectors and : A. give 3 examples of chemical products classified under the subsector, and B. list 2 applications for the chemical products.

6 CHEMICAL SUB Sectors Basic/Commodity Chemicals Speciality Chemicals Fine Chemicals Pharmaceutical Consumer products Agricultural Chemicals One Of the six subsectors listed above, choose 2 chemical sub sectors and : A. give 3 examples of chemical products classified under the subsector, and B. list 2 applications for the chemical products.

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter33: Automated Methods Of Analysis

Section: Chapter Questions

Problem 33.4QAP

See similar textbooks

Similar questions

The average copper grade of the ore is 0.7 %. The total pregnant solution flowrate from all the leach pads is 8 000 m3/hr, with an average concentration of 1.8 kg/m3, with the concentration of copper in the lixiviant that is irrigated onto the heap being 0.2 kg/m3 (ignore any solution or copper losses to the environment in these calculations). What is the average copper recovery for the process?
An aquifer contaminated with petroleum is found to have the following component concentrations at a particular site: benzene 158 ppm toluene 124 ppm ethylbenzene 91 ppm xylene 45 ppm n-heptadecane 161 ppm pristane 84 ppm Provide an estimate for the age of the spill at this site using (a) BTEX ratio and (b) nC17:Pr ratio. Show your calculations and use units throughout. Give proper s.f. for the answer.
Chemistry An aquifer contaminated with petroleum is found to have the following component concentrations at a particular site: benzene158 ppm toluene124 ppm ethylbenzene91 ppm xylene45 ppm n-heptadecane161 ppm pristane 84 ppm Provide an estimate for the age of the spill at this site using (a) BTEX ratio and (b) nC17:Pr ratio. Show your calculations and use units throughout. Give proper s.f. for the answer.
Hot mix asphalt (HMA) is commonly used in the construction of roadways in the United States at a rateestimated to be 500,000,000 tons/year. A typical upper layer (there may be as many as 5 layers ofdifferent thicknesses and compositions) of a high-volume highway is composed of crushed stone (alsoknown as crushed aggregate) and asphalt binder and is approximately 1.25 inches thick. The stone,which has a specific gravity of about 2.7, is mixed with asphalt binder (SG = 1.03) to form the HMAwith a composition of approximately 95 wt% aggregate and 5% asphalt. What is the volume ft3 of asphalt binder and weight (tons) of HMA required for the top layer of a 15-mile segment of interstatehighway with 5 lanes, each of which has a width of 12 ft?
1 Report on how to decrease the droplet evaporation time for liquidfuel combustion.
A box arrives from an instrument vendor with the new HPLC system your company ordered. You have been asked to unpack the box so the instrument can be installed. As you unpack, you find a component that was apparently incorrectly included in the shipment. Which is the incorrect component? computer hardware and interface cables injection valve solvent mixing cell flame ionization detector absorbance detector with a low volume liquid cell software for instrument operation and data analysis stainless steel column packed with microparticulate silica that is chemically modified solvent degasser high pressure solvent pumps
Dd.36. With explanation please .....
liquid hydrogen (LH2) tank is a double-hulled tank composed of cold drawn and annealed 316 stainless steel, with the cryogenic liquid on the inside and vacuum in the annular space (the outer tank). The Yield Stress of 316 stainless steel is 45 MPa, the Ultimate compressive strength is 90 MPa, the elongation % is 30, Poisson's ratio is .3 and the CTE is 15.9 *10-6 C-1. A. If there are no relief valves and the vessel is new, if the cross-sectional area of the inner tank is 1 m2, determine the force necessary to cause the tank to rupture.
A liquid hydrogen (LH2) tank is a double-hulled tank composed of cold drawn and annealed 316 stainless steel, with the cryogenic liquid on the inside and vacuum in the annular space (the outer tank). A) What factors might lead to the failure of the LH2 tank? B) Associate each factor from part A with a failure mechanism. C) What can you do to prevent the LH2 tank from failing? What can you also do to prevent the release of flammable and explosive gas?
What arc the advantages of microfabricated ISEs? Describe typical applications of this type of sensor.
Consider a soil with bulk density of 1.43 g/cm3 soil. Sampling the top 7 inches of this soil and measuring the cation exchange capacity (using the ammonium acetate method) results in the following cations exchanged by NH4+: 6.6 cmol Ca2+/kg soil, 2.7 cmol Mg2+/kg soil, 1.3 cmol K+/kg soil, and 1.3 cmol Al3+/kg soil. How much K+ is present on the CEC in the top 7 inches of each acre of this soil (in ppm K)?
Please answer atleast 4 sub-parts. Thank you.