For a sand filtration device, the flow rate of the influent is 30 m3/day with the sand filter area of 10 m². Which of the following is wrong? O A. This is a high-rate sand filter O B. This is a slow sand filter O C. The sand filter has a loading rate of 3 m3/(d-m2) O D. Sand filter requires backwash or replacement at certain frequencies.

For a sand filtration device, the flow rate of the influent is 30 m3/day with the sand filter area of 10 m². Which of the following is wrong? O A. This is a high-rate sand filter O B. This is a slow sand filter O C. The sand filter has a loading rate of 3 m3/(d-m2) O D. Sand filter requires backwash or replacement at certain frequencies.

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter4: Least-squares And Calibration Methods

Section: Chapter Questions

Problem 12P

See similar textbooks

Similar questions

Calculate volume and weight of sludge generated in thickener by chemical coagulation.Data given as:Wastewater flow: 10000 m3/dInlet concentration: 1100 mg/LFeCl3 added: 500 mg/LCaO added: 400 mg/LOverall particle removal efficiency: 80%Sludge’s specific gravity: 1.05Sludge’s moisture content: 95%Assume STANDARD chemical reactions and their product’s behavior as:FeCl3 + H2O → Fe(OH)3CaO + H2O → Ca(OH)2
9. The method described in Problem 5-8 is to be used for the analysis of ores that assay about 1.2% gold. What minimum sample mass should be taken if the relative error resulting from a 0.4-mg loss is not to exceed(a) -0.1%? (b) -0.4%? (c) -0.8%? (d) -1.1%? Here is the number 5-8 5. Describe at least three ways in which a systematic error might occur while using a pipet to transfer a known volume of liquid.6. How are systematic method errors detected?7. What kind of systematic errors are detected by varying the sample size?8. A method of analysis yields masses of gold that are low by 0.4 mg. Calculate the percent relative error caused by this result if the mass of gold in the sample isa. 500 mg. b. 50 mg. c. 150 mg.d. 70 mg.
Assume you have 0.5 m3 of soil with a porosity of 40% and an oven-dry weight of 700 kg. Calculate the bulk density. Next, assume that I drive over the soil with heavy equipment, compact the soil, and reduce the porosity from 40% to 20%. Calculate the bulk density after compaction.
1. Which of the following types of filter are made to operate continuously? a. rotary drum b. gravity c. filter press d. leaf filter 2. The filter medium resistance is controlled by I. pressure drop II. flowrate a. only a is correct b. only b is correct c. none are correct 3. In filtration, which of the following conditions will yield to a higher resistance? a. none of these b. fluid with low viscosity c. slurry with high solid concentration d. large are of filter e. low cake compressibility
The average copper grade of the ore is 0.7 %. The total pregnant solution flowrate from all the leach pads is 8 000 m3/hr, with an average concentration of 1.8 kg/m3, with the concentration of copper in the lixiviant that is irrigated onto the heap being 0.2 kg/m3 (ignore any solution or copper losses to the environment in these calculations). What is the average copper recovery for the process?
Using a 25mL pipette, you prepare a standard solution by pipetting 25.00mL of the standard iron solution[0.25g/L] into a 500mL volumetric flask. Then, using a 10mL pipette you transfer a 4mL aliquot of this solution into a 50mL volumetric flask and dilute up to the mark. Calculate the % uncertainty.
W00d chips are t0 be dried in a r0tary drier fr0m 35% m0isture to 12% m0isture. If 10 kg of wet w00d is charged/min, h0w much pr0duct can be 0btained 0ver an 8hr peri0d? Find the rati0 of kg water evap0rated/kg wet w00d charged.
A fly ash aerosol of monodisperse particles with a density of 2.0 g/mL and particle diameter of 10.0 mm has a concentration of 1000.0 mg/m3. Calculate the settling velocity in cm/s and the settling rate in g/m2-s. Please answer very soon will give rating surely
A 60-year-old woman who weighs 75kg requires a loading dose of an antibiotic to treat an infection. A plasma concentration of 4.5 mg/L of the antibiotic needs to be achieved for optimal therapeutic effectiveness. The volume of distribution (Vd) of this antibiotic is 0.2 L/kg. The salt factor (S) is 0.6 and bioavailability fraction (F) is 1. The antibiotic is available as a 100 mg/mL infusion.Loading dose = Amount of drug in the bodyBioavailability (F) x Salt fraction (S)Amount of drug in the body = Target conc. (C) x Volume of distribution (Vd)How many millilitres of antibiotic infusion need to be administered?State your answer to 1 decimal place.unit- ml
An aquifer contaminated with petroleum is found to have the following component concentrations at a particular site: benzene 158 ppm toluene 124 ppm ethylbenzene 91 ppm xylene 45 ppm n-heptadecane 161 ppm pristane 84 ppm Provide an estimate for the age of the spill at this site using (a) BTEX ratio and (b) nC17:Pr ratio. Show your calculations and use units throughout. Give proper s.f. for the answer.
1. Samples that should not be stored should be prepared/analyzed as soon as possible, especially for measurement…a. hardnessb. Nitritec. Conductivityd. Phenol 2. The following are general sample treatments in pesticide analysis, except…a. Extractionb. Cleaningc. Concentrationd. Filtering
The volume of the solution that can be measured with 5-10 microliter pipette and 2-20 microliter pipette is 0.005-0.01 mL and 0.002 mL-0.02 mL. The volume of the solution that can be measured with 20-200 microliter is 0.02-0.2 mL. The volume 1 mL of solution is measured with 100-100 microliter which has capacity of 0.1 mL to 1 mL. What would the display read for 0.10 mL, 0.20mL, 0.40mL, 0.60 mL, 1.0 mL read when using the micropipettes mentioned above