6, If the Bourdon Scale is used in two places, one is too high and the other is too low above sea level, will the reading of the scale change? Why? 7. Does the error rate in the gauge increase or decrease when the pressure is increased? And why? 8. If the gauge to be calibrated measures pressure to (kN / m2 3500) and we have the same weights, what will be the diameter of the calibration cylinder (or piston diameter)? e 6:43

6, If the Bourdon Scale is used in two places, one is too high and the other is too low above sea level, will the reading of the scale change? Why? 7. Does the error rate in the gauge increase or decrease when the pressure is increased? And why? 8. If the gauge to be calibrated measures pressure to (kN / m2 3500) and we have the same weights, what will be the diameter of the calibration cylinder (or piston diameter)? e 6:43

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the vernier gauge reading for a specimen is 21.22 mm and the average DTI observation is 3 divisions, find the actual size of the specimen in mm.
Please answer only when you are sure and give correct answer Thedensity of an oil at 23°C is 750kg / (m ^ 3) Find its relative density and kinematic viscosity if the dynamic viscosity is 5 * 10 ^ - 3 * kg / m * s .
A The Crosby gage tester shown in the figure is used to calibrate or to test gages. When the weights and the piston together weigh 105 N, the gage being tested indicates 150 kPa. If the piston diameter is 30 mm, what percentage error exists in the gage?
Give some examples of Other Pressure Measurement Devices?
If the gauge pre ssure in a 50-gal tank half-filled with liquid is 100 lbf/in .2, what would bethe gauge pressure if the tank were empty?
(1) A simple, vertical U-tube manometer is used to measure the differencebetween two gas pressures.Write down an equation for the pressure difference in terms of the difference inthe level of the fluid in the manometer. Describe briefly, with the help ofdiagrams, two modifications to the basic design which offer greater sensitivity tosmall pressure differences. Give equations for their use. ii) An extractor fan draws air from a room and delivers it to the surroundingsthrough a 5m long circular duct of diameter 0.1m. The friction coefficientfor the duct flow is 0.002. The fan characteristic, relating its total pressurerise, ∆P (Nm-2) to the volume flow rate is: ∆P = 103−7x104Q 2. What is therate of flow through the duct?You may assume that the room and surroundings are both at atmosphericpressure; state and justify any other assumptions you make.
The sketch shows an oil manometer that is connected between two pipes which transport water. The density of water can be taken as 998kg/m3, the specific gravity of glycerol is 0.76 and atmospheric pressure is 100 kPa. The respective dimensions (as shown on the sketch) are given below: h1 = 0.17 m h2 = 350 mm h3 =15cm. If the pressure gauge gives a reading of 19 kPa, what is the absolute pressure in pipe B?
For each of the following statements, answer TRUE or FALSE and explain your answer briefly. In the calibration of analytical balance for scale value, the measured mass is directly compared to the nominal value of standard mass.
In the figure shown below, an open manometer is connected to a pipe to measure the pressure at A. Fluid at A is oil of s.g. oil = 0.85 , the value of (x = 334 mm) and the value of ( y = 400 mm) to obtain the pressure intensity as gauge pressure as well as absolute pressure. Take Patm = 1.01396 bar , and the manometer fluid s.g. Hg=13.6 2-Gage pressure at A (PAgage) is equal to -----------? 1-Absolute pressure at A (PAabs) is equal to -----------?both answer in kN/m^2
As an instrumentation engineer you are asked to measure pressure with accuracy rate of±0.1%, what does it imply?If the pressure actual readings are 2, 4, 5 kg/m2in the full scale division of 10 kg/m2then whatare the possible measured values of pressure if accuracy rate of instrument is ±0.1% FSD ?State your answer with justification for the following whether it is accurate and precise,accurate not precise, precise but not accurate and not accurate and not precise.
I'm looking for a conclusion based on this given result from the Falling sphere viscometer.
Pressures up to 2000 atm are measured with a dead-weight gauge. The piston diameter is 4 mm. What is the approximate mass in kg of the weights required? [Write your answer to the nearest whole number]