Answered: 6. A printer head moves 15.6 cm from…

6. A printer head moves 15.6 cm from the left margin of the paper to the location where a line starts. The time required for the move is 0.030 second. What is the average speed of the printer head?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(6 )Suppose you're standing on the ground and throw a frisbee. You want the expression for the acceleration of a point on the edge of a frisbee (flying, rotating disk) in flight relative to yourself. If you know the acceleration of the frisbee's center of mass relative to yourself and the position of your point of interest on the frisbee's edge relative to the frisbee's mass center at a particular instant, what other information would you need? nothing - you have all the information you need the frisbee's angular acceleration the frisbee's angular velocity the frisbee's angular velocity and angular acceleration
Dynamics problem The acceleration of a point moving on a vertical line is given by the equation a = 12t – 20. It is known that its displacement s = -10 m at time t = 0 and that its displacement s = 10m at time t = 5 seconds. Derive the equations for itsa.) velocity andb.) displacement
Fix my MATLAB code. % Define unknown quantities in x-y system % abc = Acceleration of B wrt C on beam CD in i direction % vbc = Velocity of B wrt C on beam CD in i direction % xacd = Angular acceleration of beam CD in k direction % xvcd = Angular velocity of beam CD in k direction syms abc vbc xacd xvcd; % Create Unit Vectors in x-y coordinates i = [1,0,0]; j = [0,1,0]; k = [0,0,1]; % Create Unit Vectors in X-Y coordinates (R is rotation Matrix) Theta = 150; % Angle from X-axis to x-axis R = [[cosd(Theta),-sind(Theta), 0]; ... [sind(Theta), cosd(Theta), 0]; [0, 0, 1]]; XYZ = R*[i;j;k]; I = XYZ(1,:); J = XYZ(2,:); K = XYZ(3,:); % Set known quantities for Beam AB (no slider connection). xVab = -2.5*K; % Angular Velocity of Beam AB xAab = -3*K; % Angular Acceleration of Beam AB Rba = 0.2*(cosd(135)*I + sind(135)*J ); % Vector from A to B in X-Y % Calculate velocity and acceleration of point B % due to rotation of Beam AB (no slider connection). Vb1 = cross(xVab,Rba); Ab1 =…
Solve the inverse kinematic problem for the following 6 DOF robot, using the method ofkinematic decouplingif it is known that its Denavit-Hartenberg parameters are as shown in the table inthe table
Solve the inverse kinematic problem for the following robot of 6 DEGREES OF FREEDOM, using the method ofkinematic decouplingif it is known that its Denavit-Hartenberg parameters are those shown in thetable
No.16: a.) Describe the Bicubic patches with mathematical functions. b.) Enumerate various desired modeling facilities required for Industries.
Context The needle of a sewing machine makes a repetitive up and down motion which is described by the equation y(t)=Acos(wt) To choose the settings of the device that will ensure that the needle successfully pierces the textile, you are asked to model the speed in ? of the needle as a function of time. Constraints and information The parameter A represents the range of motion (in m);The parameter w represents the angular frequency. It tells us about the number of back and forth movements that the needle makes per second;The parameter w is given in rad/s, so your calculator absolutely must be in radians mode to do the calculations in this problem;Modelization Establish the model for the y velocity of the needle as a function of time and the parameters A and w. Then test your model by calculating the speed in y of the needle at the moment and with the given parameters: Moment: 4.1 s Amplitude: 0.012 m Angular frequency: 17.9 rad/s
Kinematics question. Solve using Instantaneous centre of Velocity.
Help with the MATLAB code to do the following: Given an audio recording of vehicles, compute Power Spectral Density, 1/3 octave band level, octave band level, A-weighted Leq, C-weighted Leq, L10 (unweighted since sample is short), L90 (unweighted since sample is short). If the measurement is made at approximately 50 ft, and that the vehicles are moving at an average of 65 mph, what is the flow rate Q? If instead, the noise is dominated by 1-2 motorcycles, how fast are they going? Given- -The data are in counts -Calibration factor is 133 uPa/count -Sample rate is 44100Hz. -Remember that in air the dB reference is 20 uPa -Pwelch requires that the inputs are doubles
Hello, I'm having difficulty undertanding this kinematics equation. A step by step answer would be appreciated. Thank you.
You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 d) Knowing that the distance travelled by an object is the area under its velocity-time graph, determine the distance travelled by the end effector on the interval 0 =< t =< 1 by using the mid-ordinate rule. Simpson’s rule correct to 3 decimal places using four intervals. e) Calculate the same distance as in (d) above by using the appropriate definite integral. f) Compare the distances you calculated in (d) and (e) above and comment on the accuracy of the two methods you used in (d)
You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 Use your knowledge of differentiation to sketch the velocity-time graph, clearly marking the critical points. Using the graph sketched in (a) above, estimate the velocity when t = 1.5 s Calculate the velocity of the function when t = 1.5 s by substituting to the velocity function. Compare this value to the value you estimated in b above.