A joint is subject to a cyclic loading. There is an acceptable preload of 1,200 lbs, and the axial load is fully reversed with an amplitude of 1,600 lb. THe tensile bolt area is 0.160 in^2. Ignore any design factors and (take all nd=1) and assume the loads include the 1.2 bolt factor. If the joint constant is 0.25, the alternate and means axial stress for the bolt are:

A joint is subject to a cyclic loading. There is an acceptable preload of 1,200 lbs, and the axial load is fully reversed with an amplitude of 1,600 lb. THe tensile bolt area is 0.160 in^2. Ignore any design factors and (take all nd=1) and assume the loads include the 1.2 bolt factor. If the joint constant is 0.25, the alternate and means axial stress for the bolt are:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
(7) A universal joint shown has a pin whose Sy = 485N/mm2 & d = 15mm. Its pin-bush has a length a = 62mm. The shaft turns 400rpm. (a) What is the torque that maybe transmitted for shear with a factor of safety = 5; (b) In order not to have excessive wear on the pin, the average bearing pressure should not exceed 20x103 kPa, compute the transmitted torque. (c) What is the transmitted power in both cases?
A right angled bell crank lever is to be designed to raise a load of 5 kN at the short arm end. The lengths of short and long arms are 100 and 450 mm respectively. The lever and the pins are made of steel 30C8 (S = 400 N/mm2). And the factor of safety is 5.the permissible bearing pressure on the pin is 10 N/mm². The lever has a rectangular cross section and the ratio of width to thickness is 3:1. The length to diameter ratio of the fulcrum pin is 1.25:1. Calculate (i) The diameter and length of the fulcrum pin (ii) The dimensions of the cross section.
A semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.
(9) A Mercedes Benz gas engine valve spring should not exceed to a cylindrical space of 1¾-in in diameter. The spring index is 6.0 & the maximum load it will have to sustain is l00lb with corresponding deflection of ½-in. The spring is subjected to repeated loading & fatigue must be considered, a low working stress of 40,110psi will be used. Determine: (a) the diameter of wire based on commercial sizes; (b) the number of coils.
A motor is to transmit 150 kW to a piece of mechanical equipment. The power is transmitted through a solid structural steel shaft. Failure is by yielding, and the factor of safety is 1.25. The designer has the freedom to operate the motor at 60 rpm or 6000 rpm. For each case, determine the minimum shaft diameter. Shafts are available with diameters in increments of 5 mm. If weight is important, which speed would be used?
A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in diameter and 92mm thick and the flange web are 19 mm thick. Six 16 mm bolts in a 165 mm diameter circle connect the flange.The keyway is 6 mm shorter than the hub’s thickness and key is 14 mm x 14 mm. Coupling is to transmit 45 KW at160 rpm. For all parts, yield point value in shear is one – half the yield value which is 448 MPa. Calculate the forceon the shaft
A shaft subjected to bending moment varying from -200 N m to +500 N m and a varying torque from 50 N m to 175 N m. If material of the shaft is 30C8, stress concentration factor is 1.85, notch sensitivity is 0.95 reliability 99.9% and factor of safety is 1.5, find the diameter of the shaft. The load on a bolt consists of an axial pull of 10 kN together with a transverse shear force of 5 kN. Find the diameter of bolt required according to Maximum principal stress theory; Maximum shear stress theory; Maximum principal strain theory; Maximum strain energy theory; and Maximum distortion energy theory. Take permissible tensile stress at elastic limit = 100 MPa and poisson’s ratio = 0.3
A polyamide F-0 flat belt 80mm wide is used to transmit 5 kW under light shock conditions where Ks = 1.25, and a factor of safety equal to or greater than 1.1 is appropriate. The pulley rotational axes are parallel and in the horizontal plane. The shafts are 8mm apart. The 50 mm driving pulley rotates at 1750 rev/min in such a way that the loose side is on top. The driven pulley is 50 mm in diameter. The factor of safety is for unquantifiable exigencies. (a) Estimate the centrifugal tension Fc and the torque T. (b) Estimate the allowable F1, F2, Fi and allowable power Ha . (c) Estimate the factor of safety. Is it satisfactory?
An engine valve spring must exert a force of 300 N when the valve is closed and 500 N when the valve is open as shown in Figure 3. The maximum lift of spring is 8 mm (ymax). With a safety factor of 1.6 a. Design the wire diameter. b. Calculate the number of active coils. c. Calculate the number of total coils and the free length. d. Check the stability. Design Decisions: The spring is made of ASTM, A227, unpeened, clash allowance of 0.15, G = 79 GPa, squared and ground ends and C = 6.
A circular bar of L 570mm length is supported freely at its two ends. It is acted upon by a central concentratedcyclic load having a minimum value of 20 kN and a maximum value of 50 kN. Take a factor of safety of1.5, size effect of 0.85, and a surface finish factor of 0.9. The material properties of bar are given as ultimatestrength of σu 625MPa, yield strength of σy 510MPa and endurance strength of σe 340MPa. Determine thediameter of bar by using Goodman’s method and Soderberg method.
The preliminary design of a large shaft connecting a motor with agenerator requires the use of a hollow shaft with inside and outside diameters4 in. and 6 in., respectively. Taking a safety factor of 2.5 andknowing that the shear resistance is 14 ksi, determine the maximumtorque that can be transmitted by the shaft as designed