600 kN 300 mm 80 mm 60 mm 160 mm -y 80 mm

Q: The rotor shaft of the helicopter is subjected to the tensile force and torque shown when the rotor…

A:

Q: The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point B,…

A: d=1in Draw the free diagram of the problem by converting the eccentric loads into the loads and…

Q: The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC,…

A: Given data as per question Diameter of cable AB = 12mm Diameter of cable AC = 10mm Mass = 2 Mg =…

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: Determine the stress in the cable BC if the mass of the cylinder is 250 kg. The cross sectional area…

A:

Q: ) If the load has a weight of 600 lb, determine the maximum normal stress developed on the cross…

A: An internal resisting force which is applied by the molecules of the object so that the shape of the…

Q: The screw of the clamp exerts a compressive force of 500 lb on the wood blocks. Determine the…

A: Area at section (a-a) Moment of inertia at section (a-a)

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A: The forces and torques at point B are shown as, On using equilibrium of forces in x, y, and…

Q: The sign is subjected to the uniform wind loading. Determine the stress components at points C and D…

A: Determined the projection area of the signboard. Find the wind force

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

A:

Q: The sign is subjected to the uniform wind loading. Determine the stress components at points A and B…

A: Given Load = 1.5 KPa To find Stress component at point A and B with representation of result on a…

Q: The column is subjected to an axial force of 8 kN which is applied through the centroid of the…

A:

Q: The rod has a diameter of 1 in. and a weight of 10 lb>ft. Determine the maximum torsional stress…

A: diameter of rod (d) = 1 in. weight of rod (w)    = 10 lb-ft the FBD of the cut segment of the rod is…

Q: 1. The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A…

A: To find: The longitudinal and hoop stress developed in the wall of the pipe, also draw the stress on…

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A:

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is…

A: Introduction: The tension is created by fighting the bursting effect of the imposed internal…

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: Given:- P=2kip,Width of section of bar with hole,w1=1.875 inch,Width of section of bar without…

Q: The rod has a diameter of 1 in. and a weight of 15 lb>ft. Determine the maximum torsional stress…

A: Given: The diameter of rod is D = 1 in. The weight of the rod is M = 15 lb/ft. The length of the…

Q: Determine the average punching shear stress the circular shaft creates in the metal plate through…

A: Given data: The value of shear load is F=40 kN The diameter of shaft is dAB=50 mm The thickness of…

Q: The steel water pipe has an inner diameter of 12 in. and a wall thickness of 0.25 in. If the valve A…

A: Given Data: The inner diameter of the pipe is d = 12 in. The thickness of the pipe is t = 0.25 in.…

Q: The copper pipe has an outer diameter of 3 in. and an inner diameter of 2.5 in. If it is tightly…

A: Given Data: The outer diameter of shaft is d0 = 3 in. The inner diameter of shaft is di = 2.5 in.…

Q: he shaft is loaded with torque and force acting at location B and C. Given the diameter of 1 in.,…

A:

Q: The rod has a diameter of 40 mm. If it is subjected to the force system shown, determine the stress…

A: Understand that the point A lies on the outer periphery of the shaft on the z axis. The Torsional…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A: force=8 kN (a) average normal stress in the shank                          σs=PA=…

Q: The spreader bar is used to lift the 2000-lb tank. Determine the state of stress at points A and B,…

A: Given data as per question weight of tank =2000 lb ∑Fy=02000−2Fcos30=0F=1154.7 lbInternal forces and…

Q: Determine the average normal stress developed in rod AB if the load has a mass of 64 kg. The…

A:

Q: the internal pressure is 2 MPa. Determine the maximum she stress in the cylindrical tank.

A: For solution refer below images.

Q: The resulting stress distribution along section AB for the bar is shown. From this distribution,…

A:

Q: Determine the shear stress at point A on the surface of the shaft. Represent the state of stress on…

A: Write the twisting moment at the cross section containing point A.

Q: The solid bar has a diameter of 50 mm. The two forces and the torque Tx are acting at the origin of…

A:

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the state…

A: The given beam is subjected to three loads- axial load, shear load and bending moment. Therefore…

Q: The sign is subjected to the uniform wind loading. Determine the stress components at points A and B…

A: Point A:             σA=McI=10.5×103×0.05π40.054=107 MPa               τA=TcJ=3×103×0.05π40.054=15.3…

Q: Determine the location of the centroid, y, and the moment of inertia of the cross section about the…

A: To find the centroid…

Q: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown, determine…

A: Writing equilibrium equations:→∑FY=0 ⇒-P+∫04[(15.x)×(dx×0.5)]=0⇒P=15×23×[x23] 04×0.5⇒P=40 MNNow…

Q: The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC,…

A: Given: The mass of the concrete pipe is m=2 Mg. The diameter of the cable AC is d’=10 mm=0.01 m.…

Q: QI/If the beam is subjected to a shear force of V= 80 kN, determine the shear stress developed at…

A:

Q: If the block is subjected to a centrally applied force of P = 6 kip, determine the average normal…

A: The area of the cross-sectional = 14(6)-2(1)(4)=76 in2 σavg=PAσavg=676=0.0789 ksiσavg=PA=78.95 psi

Q: If the load has a weight equivalent to 5 kN, determine the maximur hormal stress on the cross…

A: Given Data Load is :P=5 kN=5000 N Radius of circle is :r=2 cm=20 mm Distance of CD is : LCD=50…

Q: Determine the state of stress at point A on the cross section of the pipe assembly at section a-a.…

A:

Q: If the extended stress at the pointpin the level and at n= 1+j+ k is given by matrix 10 2 222 the…

A:

Q: Determine if the stress in the steel section, aluminum section, and bronze section are compression…

A:

Q: 7-46. The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and…

A: Given, Mass of pipe, m=2 Mg=2000 kg The diameter of the cable AB, dAB=12 mm The diameter of the…

Q: The solid rod has a radius of 0.1 m. If it is subjected to the forces of 50 kN, 60 kN, and 80 kN,…

A:

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A:

Q: The elbow of the pipe has an outer radius of 0.75 in. and an inner radius of 0.63 in. If the…

A: Given, M= 25 lb.in

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. The pipe is fixed at…

A:

Q: F7-10. If the 600-kN force acts through the centroid of the cross section, determine the location y…

A: force acts through the centroid of the cross section=600 kN

Q: Two spanners are used to tighten the pipe. If P =200 N is applied to each spanner, determine the…

A: Given:P=200 ND=25 mmd=20 mm

Q: 15 kN-m 30 kN-m 75 kN-m 30 kN-m

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.