7) In one device, the disc is held in place by a torsion spring and an adhesive damper. Mass inertia torque, J of this disk is equal to 7.2 * 10-6 kg.m² . The vibration period of this disk is 4.2 seconds and the damping ratio of this system is 0.5399. Find: A) A)Natural frequency B) Spring stiffness and damping of the adhesive damper

7) In one device, the disc is held in place by a torsion spring and an adhesive damper. Mass inertia torque, J of this disk is equal to 7.2 * 10-6 kg.m² . The vibration period of this disk is 4.2 seconds and the damping ratio of this system is 0.5399. Find: A) A)Natural frequency B) Spring stiffness and damping of the adhesive damper

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mechanical engineering question, An undamped vibrating system is given that having natural frequency is 100 rad/s. A damper with a damping factor of 0.8 is attached to the system.Calculate the frequency of vibration of the damped system?
A vibrating system with mass 3 kg, stiffness 21 N-s/m and damper having damping coefficient 10 N-s/m When an exciting force of magnitude 27 sin2t is acting, what would be the time period of oscillations?
A spring-mass system with m = 0.5 kg and k = 10,000 N/m, with negligible damping, is used as a vibration pickup. When mounted on a structure vibrating with an amplitude of 4 mm, the total displacement of the mass of the pickup is observed to be 12 mm. Find the frequency of the vibrating structure.
A washing machine with a mass of 60 kg and a drum radius of 15 cm, rotates at 1000 rpm and washes 3 kg of unbalanced laundry. a) How much dynamic force would be transmitted to the ground if no vibration isolation was taken from the machine?b) What would be the stiffness (k) of the visco-elastic floor if an insulation measure with a damping ratio of 0.1 was taken, which would reduce the force transmitted to the floor by 90%?
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
A block of mass m = 16 kg oscillates attached to a spring of spring constant K = 162 N/m. The motion of the block is also acted upon by a damping force proportional to the velocity of the form Fd = -bv, where b = 36√ 2 kg/s. The system is excited by a sinusoidal force of maximum value F0 = 7 N. If the excitation frequency varies, at what frequency ω (in rad/s) will resonance occur? Choose the closest value. a) 63/4 rad/s b) 9/28 rad/s c) 567/4 rad/s d) 9/4 rad/s
A compact object with a mass of 8.80 kg oscillates at the end of a vertical spring with a spring constant of 1.60 ✕ 104 N/m. The motion is damped by air resistance, and the damping coefficient is b = 3.00 N · s/m. (a) What is the frequency (in Hz) of the damped oscillation? Hz (b) By what percentage does the amplitude of the oscillation decrease in each cycle? % (c) Over what time interval (in s) does the energy of the system drop to 5.00% of its initial value? s (d) What If? The atmosphere of Venus is 50 times thicker than that on Earth. If the effect of air resistance on Venus is represented by b = 150 N · s/m, recalculate the answers for parts (a) to (c) for this system if it is set in motion in the atmosphere of Venus. What is the frequency (in Hz) of the damped oscillations? Hz What is the percentage decrease in amplitude in each cycle? % What is the time interval (in s) for the energy to drop to 5.00% of its initial value? s
A vibrating system with a mass of 12 kg and a sprinf with a stiffness of 120 N/m. The mass is started in motion from equilibrium position with an initial velocity of 2 m/s in the upward direction and with an applied external force F(t) = 7sint. While in motion the mass is subjected to damping with damping constant of 72 kg/s. 1. Find the position of the mass (natural response) at any given time. 2. Find the position of the mass (forcedresponse) at any given time. 3. Find the position of the mass (complete response) at any given time. 4. Find the position of the mass (natural response) after 3s. 5. Find the velocity of the mass (natural response) after 3s. 6. Find the position of the mass (forced response) after 3s. 7. Find the velocity of the mass (forced response) after 3s. 8. Find the position of the mass (complete response) after 2s.
A spring-mass-damper system oscillating about the horizontal surface is subjected to anexternal force of F = 300 sin (6)(t), where 300 is in Newtons and 6 is in radians per second. Thesystem has a mass 90 [kg], a damping coefficient of 78 [N ⋅ s/m] and a spring constant of300 [N⁄m]. The system is both given an initial displacement of 1.2 [m] and an initial velocity of 1.4[m⁄s].a. Using Method of Undetermined Coefficients, determine the particular solution for thedisplacement function.b. Determine the unknown coefficients for the homogeneous solution using the initialconditions (Note: the external force already works at t = 0).c. Determine the position, velocity, and acceleration of the system after 10 seconds.
Suppose that the motion of the adjustable roller has a damping coefficient b, and that the force exerted by the rolled material on the adjustable roller is proportional to the material's change in thickness: f=c(T-x). Suppose further that the DC motor has a torque constant K, and a back- emf constant Ke, and that the rack-and-pinion has effective radius of r. In reality the thickness of the input material. T. is one of the inputs. but here for simplicitv assume T is constant. Do not neglect the weight of the adjustable roller and assume mg = cT. The input of the system is the voltage of DC-motor and the output is the thickness of the output material ,x. 1. Draw free body diagram of adjustable roller 2. Prepare a mathematical block diagram showing mathematical relations in terms of the transfer functions. The block diagram should at least contains a block for DC-motor and a block for mechanical system (i.e gears and adjustable rollers) 3. Determine transfer function G(s)=X(s)/Vs(s) 4.…
Two mass-spring systems are experiencing damped harmonic motion, both at 0.7 cycles per second and both with an initial maximum displacement of 12 cm. The first has a damping constant of 0.6, and the second has a damping constant of 0.2. a. Find functions of the form to model the motion in each case. b. How do they differ? (Hint: graph the two functions)
If a mass of 6 kg oscillates on a spring having a mass 3 kg and stiffness 11200 N/m, then the natural frequency of the system in rad/sec will be