Please help me answer number 7. Please show a CLEAR and READABLE solution/s. Thanks!!! The course subject is Electrical Machines 1.NOTE: The answer is given on the bottom side of the image. Could you show me the solution to how to get it? Super thanks!!! 7.A d.c. series motor on full-load takes 50 A from 230 V d.c. mains. The total resistance of the motoris 0.22 2. If the iron and friction losses together amount to 5% of the input, calculate the powerdelivered by the motor shaft. Total voltage drop due to the brush contact is 2 A. (10.275 kW)

Given: The load current is 50 A The voltage is 230 V the resistance of the motor is 0.22 ohms The…

7. A d.c. series motor on full-load takes 50 A from 230 V d.c. mains. The total resistance of the motor is 0.22 2. If the iron and friction losses together amount to 5% of the input, calculate the power delivered by the motor shaft. Total voltage drop due to the brush contact is 2 A. (10.275 kW)

7. A d.c. series motor on full-load takes 50 A from 230 V d.c. mains. The total resistance of the motor is 0.22 2. If the iron and friction losses together amount to 5% of the input, calculate the power delivered by the motor shaft. Total voltage drop due to the brush contact is 2 A. (10.275 kW)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Related questions

Q: For the circuit shown below, thevenin voltage at terminals a-bis 50 www 0.51, 1A 50² ba ob 10 V

A: Given circuit- To find- Thevenin voltage.

Q: What is a typical voltage used for capillary zone electrophoresis? a. 2.5 MV b. 250 kV c. 250 MV d.…

A: capillary zone electrophoresis

Q: 6. Find v(0*). a) -5 V b) 10 V c) -15 V d) 20 V e) none of these 7 Find (E) 10 V 2 kn ww t=0 20 mH…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: 4-pole Q-1. A 440 V, 50 Hz, 37.3 Kw, 3-phase, star-connected induction motor has per phase stator…

A: Induction Motor A conventional AC electric motor is an induction motor, also referred to as an…

Q: a capacitor and resistor are connected in series. the resistor has a resistance of 26 ohms and the…

A: The resistance of the resistance is, R=26 Ω The capacitive reactance of the capacitor is, Xc=16 Ω…

Q: Recall the equation of the Z-parameters -- H = + V₂₁ 1 V₂ 2 I₁ U₁ 1. What is 211? 2. What is 212?…

Q: Consider the circuit below, with C = 1F and L=4H, calculate the node voltages V1 and V2.

Q: Question 05: The inputs for a positive edge triggered D flip-flop are shown in figure. Find the…

A: Given Signal:-

Q: III. Find the current Lby reducing the circuit to the right of terminals a-b to its simplest form…

A: We need to find out the current for given circuit.

Q: Design a PLL as shown in Fig. 16.58(c) so that fo = 5 kHz and fc = ±50 Hz. Assume Vcc= -VEE = 15 V.

A: PLL is conmanly use IC device. Given is the circuit diagram of PLL. Given parameters are f0 =5 kHz…

Q: need handwrite version of solutions

Q: QA) a. Sketch the output v. and determine the dc level of the output for the network of Fig. 1. b.…

A: The output of the circuit is based on the conduction of the diode. If the diode is in forward bias…

Q: Temperature dependence of resistivity

Q: Q4. Consider g(t) whose waveform and spectrum are illustrated as: g(t) G(f) 3 2 1 Assume fe 1400Hz.…

A: Given: Waveform of a signal g(t) with its spectrum G(f), fc=1400 Hz, To find: a) Sketch the…

Q: 1.) For the circuit shown in Figure 3 with the output shown, determine the following parameters:…

A: The given circuit is as shown below,

Q: the current and voltage are 64 deg out of phase in an rc series circuit. the apparent power is 260…

Q: When a source is connected to the sending-end of a transmission line by a switch that closes at time…

A: transmission line with source on sending end through a switch and switch closes at time t=0

Q: 1. Apply phasor analysis to evaluate the following: a. v = [120 sin(10t +20°) + 120 cos(10t – 121°)]…

A: In this question We need to determine the phasor voltage v and current i. Phasor Voltage V= Vm /√2…

Q: A fisherman notices that his boat is moving up and down periodically, owing to waves on the surface…

A: Given below clear explanation

Q: R= L = G = C =

A: Given data, Impedance Z0=43-j2 Ω Propagation constant γ=2+j7 m-1 Frequency f=241 MHz

Q: 11) Given the following 3-wire balanced Y-Y system, a) Calculate the Line Currents b) Calculate the…

A: In this question, We need to determine the line currents and line voltages as shown the circuit. We…

Q: Consider a unity feedback system with its forward transfer function G(s) = K/[s(s+2)(s²+2s+5)] where…

Q: A capacitor consists of two metal plates each 500 x 500 mm² and spaced 6 mm apart. The space between…

A: Given data, Constant ε0=8.85×10-12 F/m Dimensions 500×500 mm2 or 0.5×0.5 m2 Distance , d1=2 mm=0.002…

Q: Design a circuit with logic gates that deactivate three solenoid valves when the object is present…

A: According to the question, we need to design a circuit with logic gates that deactivate three…

Q: Given the NPN common emitter amplifier circuit below with I₁ = 0.105 mA, RF = 200 kN, R₁ = 80 kn,…

A: We need to find out the gm and rπ for given circuit .

Q: 2-3. +Prove the identity of each of the following Boolean equations, using algebraic manipulation: B…

A: The given Boolean expression can be reduced to the required expression by using the Boolean…

Q: 6Α 40 Ω + Vo Δια 7 ) 30 V

Q: 2.1 Combinational logic circuits. Tabulates a truth table for the following Boolean expression shown…

Q: (b) An aperiodic signal defined below is the input signal to a system is sampled at 4000Hz rate:…

Q: Question 03: Implement the following Boolean Function using Multiplexer F(A, B, C, D) =…

Q: Find the DTFT of the following signals: a) x(n) = 3 au(n) b) y(n) = 3 nau(n) where "a" is a real,…

A: Given: Discrete time signals, a) x(n)=3anu(n),b) y(n)=3nanu(n), where a is real and positive…

Q: Design the given circuit shown and determine the standard value of the load resistor operating at an…

A: Given: In this question, the given details are, The given circuit diagram is, The standard value of…

Q: ② lim 2 60 를 In (Itaex)

A: To solve integral of given question

Q: A Forward converter has the following parameters. Vin=30V, N1=10Turns, N2=5Turns, N3-10Turns. The…

A: Given below clear explanation

Q: Boolean Algebra Apply DeMorgan's theorems to each expression: a) A + B (b) AB (e) A(B + C) (f) AB +…

A: We need to simply the given Boolean expression .

Q: Fuel cells are environmentally clean. emit sulfur oxides. produce carbon…

A: Fuel cell- it converts chemical energy in electrical energy. - it uses input as hydrogen, oxygen and…

Q: 6. To raise generator voltage, the a. field current should be increased. b. field current should be…

A: basic questions on DC machines

Q: Question 6 For a phase lead compensator, the corner frequencies are 5 rad/sec and 10 rad/sec. Find…

A: Given- A phase lead compensator, Corner frequencies = 5 rad/s & 10 rad/s, To Find- The maximum…

Q: Find the currents in each of the resistors €

A: The required current through the resistor can be calculated by using the mesh current and the mesh…

Q: 3. Find the Thevenin equivalent circuit for the circuit shown in Figure 3. Then, find RL such that…

A: In this question, We need to determine the thevenin equivalent circuit. And find the maximum power…

Q: A group IV semiconductor has an intrinsic carrier concentration of 2.4×10^13 ??−3 at 300 K. a. Given…

A: Given, A group IV semiconductor has an intrinsic carrier concentration, ni = 2.4×1013 cm-3…

Q: Note that VA (early voltage) →∞. Note also that C1 and C2 are large AC coupling capacitors. (Hint:…

A: The given circuit is as shown below,

Q: d. increases the terminal output voltage. 6. Failure of a DC shunt generator to build up to its…

A: As per Bartleby guidelines as multiple MCQ questions are asked, only the first 3 namely 5, 6 and 7…

Q: compute the Fourier series of the given functions: P(+) = 5-1 -< <o f(t)= ft f(t) -4/2 4/24 + 4 L…

A: Given, f(t) = 3 cos2(t) , for -π ≤ t ≤ π We need to determine the Fourier series of f(t).

Q: A cell of internal resistance 0.2Ω is connected to two coils of resistances 6Ω and 8Ω respectively,…

A: The question is emf of the cell. Networks concept.

Q: 2. Determine the appropriate value of frequency for a square wave generator (in Hz) to measure the…

Q: Design a PLL as shown in Fig. 16.58(c) so that fo = 5 kHz and fe = ±50 Hz. Assume Vcc= -VEE = 15 V.

A: PLL is conmanly use IC device. Given is the circuit diagram of PLL. Given parameters are

Q: 3. a. Determine the dynamic (ac) resistance of the commercially available diode of Fig. 2.1 at a…

A: 3) Given data, Forward Current ID=10 mA Taking the remaining values from the graph.

Q: In the square wave signal in the figure, the duration of 1 is 0.6ms and the period is 1ms; a) What…

A: As per Bartleby guideline we need to answer the first three questions only. Kindly repost the rest…

Q: In the system with unit feedback (unity) in the figure below, the transfer function G(s) is K(s + 2)…

Concept explainers

DC Generator

An electromechanical machine which converts input mechanical energy to respective output electric energy is called a generator.

Question

100%

Please help me answer number 7. Please show a CLEAR and READABLE solution/s. Thanks!!! The course subject is Electrical Machines 1.

NOTE: The answer is given on the bottom side of the image. Could you show me the solution to how to get it? Super thanks!!!

7.
A d.c. series motor on full-load takes 50 A from 230 V d.c. mains. The total resistance of the motor
is 0.22 2. If the iron and friction losses together amount to 5% of the input, calculate the power
delivered by the motor shaft. Total voltage drop due to the brush contact is 2 A. (10.275 kW)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A dc series motor drives a load a 30rev/s and takes a current of 10A when the supply voltage is 400V. If the total resistance of the motor is 2Ω and the iron, friction and windage losses amount to 300W , determine the efficiency of the motor ANSWER:_______________%
Write the solution neatly. A 230 V d.c. shunt motor, having an armature resistance of 0.05 ohm and a fieldresistance of 75 ohms, draws a line current of 7 A while running light at 1120 rpm. Determine the motor efficiency when the line current at a given load is 46 A. Answer % = 83.92 %
According to the stator terms of a 3-phase Star connected 380 V, 5 Hp 50 H, 4-pole 1450 rpm induction motor, Rs= 0.3 ohm, Xs=0.5 ohm, R2= 0.15 ohm, X2=0.3 ohm. The idling power of the motor is 400 W. By drawing the equivalent circuit of the motor, find the power and efficiency taken from the motor when it is running at 1% slip and under full load.
Q.30 How many amperes does a 1-horsepower, 240-volt, single-phase motor draw? Select one: A. 8 AMPERES B. 4.7 AMPERES C. 4.2 AMPERES D. 8.8 AMPERES
Branch-circuit conductors supplying a single continuous-duty motor shall have an ampacity not less than _____ rating A. 125% of the motor’s nameplate current B. 125% of the motors full-load current as determined by 430.6(a)(1) C. 125% of the motor’s full locked-rotor D. 80% of the motors full-load current.
Please show a step-by-step solution. The input power to a 6-pole, 3-phase, 50 Hz induction motor is 46 kW; the speed is 950 rpm. The stator losses are 4.1 kW and the friction and windage losses are 2.1 kW. Find the efficiency, in percent, of the motor. Correct Answer: 81.97
Motors from two different manufacturers are being considered for application. Both motors are 50Hp, 460 volts, 3 phase, 60 cycles. Motor A operates at 80% efficiency and motor B operates at 89% efficiency. The expected need for the motor is 15 years. Motor A cost P120, 000.00 and motor B P150, 000.00. Electrical energy cost P8.00 per Kw-Hr and the motors will be operating 8 hours per day, 250 days a year. Assume taxes and insurance are 3% of first cost. Which motor should be purchased?
Answer letter B A 200V shunt motor develops 23hp, when taking 20.2 kW. The field resistance is 50 ohms and the armature resistance is 0.06 ohm. A. What is the total losses? a. 2512 W b. 1756 W c. 3718 W d. 3042 W B. What is are the rotational losses? a. 1125 W b. 1667 W c. 917 W d. 825 W
The power input to a 415 V, 50 Hz, 6 pole, 3-phase induction motor running at 975 rpm is 40 kW. The stator losses are 1 kW and friction and windage losses total 2 kW. What is the efficiency of motor ?
A 60 horsepower rated 230 V shunt motor has an armature circuit resistance of 0.052 ohm. The field resistance is 48.7 ohms. The motor is stated to have a maximum efficiency of 90.9%. Calculate the line current carried at maximum efficiency and the total stray power loss.
A 50 h.p, 440 V d.c. A shunt motor draws a current of 104 A from the mains when running at full load. The resistances of its shunt field winding and armature winding are 220 ohm and 0.4 ohm respectively. Then find (1) electrical efficiency (2) mechanical efficiency and (3) commercial efficiency of the motor.
A220 Vshunt DC motor rotates with speed of1800rev/min.( need handwritten only ,otherwise downvote.)