7. A load cell is calibrated in an environment at a temperature of 21°C and has the following deflection/load characteristic: Load (kg) Deflection (mm) 50 100 150 200 0.0 1.0 2.0 3.0 4.0 When used in an environment at 35°C, its characteristic changes to the following: Load (kg) Deflection (mm) 50 100 150 200 0.2 1.3 2.4 3.5 4.6 (a) Determine the sensitivity at 21 and 35°C. (b) Calculate the total zero drift and sensitivity drift at 35°C. (c) Hence determine the zero drift and sensitivity drift coefficients (in units of um/°C and (um per kg)/(°C).

7. A load cell is calibrated in an environment at a temperature of 21°C and has the following deflection/load characteristic: Load (kg) Deflection (mm) 50 100 150 200 0.0 1.0 2.0 3.0 4.0 When used in an environment at 35°C, its characteristic changes to the following: Load (kg) Deflection (mm) 50 100 150 200 0.2 1.3 2.4 3.5 4.6 (a) Determine the sensitivity at 21 and 35°C. (b) Calculate the total zero drift and sensitivity drift at 35°C. (c) Hence determine the zero drift and sensitivity drift coefficients (in units of um/°C and (um per kg)/(°C).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.16P

See similar textbooks

Similar questions

1. A sling shot was released in a vertical direction using a rubber band having an equivalent spring constant of 2N/mm. If the deflection of the rubber band amounts to 10cm and the mass of the stone is 21g, determine the maximum height (above the undeflected position of the sling) the shot can reach. Derive with the formula below, show the cancellation, explain the step by step and DRAW a free body diagram/figure. Refer with this: PE1 + KE1 + U1 + WF1 + Q1 + W1 = PE2 + KE2 + U2 + WF2 + Q2 + W2 + E losses.
A bimetallic strip is used as a sensor. The strip has a length of 20 μm. The width of the strip is 1μm. It has an upper layer made of steel (E = 210 x 10 9 N/m 2 ) and the lower layer made of aluminum (E = 80 x 10 9 N/m 2 ). Each layer is 0.1 μm thick. Determine the equivalent stiffness of the strip in the axial direction. Note that the strips are perfectly attached.
A chromel-constantan type thermocouple has a cold junction (or cold terminal) at the temperature of 20ºC. The tables provide the following values for this thermocouple: 0°C for e.m.f = 0.000 mV; 20ºC for e.m.f = 1192 mV and 200ºC for e.m.f = 13419 mV. To determine:(a) The Seebeck coefficient (or proportionality constant) of this thermocouple. (b) The electrical voltage at the thermocouple terminals when the hot junction (or terminal hot) is at a temperature of 200ºC.
While removing material from iron (atomic weight = 56, valency = 2 and density = 7.8 g/cc by electrochemical machining, a metal removal rate of 2 cc/min is desired. The current (in A) required for achieving this material removal rate is (a) 896.07 (b) 14.93 (c) 448.03 (d) 53764.29
Answer must be coorect -- when using three-wire connections to a strain gage to reduce the effects of leadwire resistance changes with temperature, a phenomenon called leadwire desensitization can occur. If the magnitude of the leadwire resistance exceeds 0.1% of the nominal gage resistance, significant error can result. Assuming a 18-gauge (AWG) platinum leadwire (resistivity 10.6×10-8 S2m) and a standard 120 22 gage, how long can the (individual) leads (in inches) be before there is leadwire desensitization?
(a) An infrared gas analyser has a span of 01% of the component being measured. It operates at atmospheric pressure and was calibrated when the barometric pressure was 0.995 bar. The barometric pressure changes to 1.015 bar. What will the instrument read when the actual percentage of the component is (i) 0.5% (ii) 0.8%?
For a given spring, in order to determine the value of the spring constant, we have attached dead weights to one end of the spring, as shown in Figure 10.5 . We have measured and recorded the deflection caused by the corresponding weights as given in Table 10.1(a) . What is the value of the spring constant? We have plotted the results of the experiment using Excel (shown in Figure 10.6 ).
Considering Figure 20-8 (textbook), the torsion geometry parameter, Jw, for case 2 when b=6 and d=9 is most likely: 400.5 562.5 283.5 60.8 279.0 392.6 386.0 572.6 184.1
Using the value of 0.55s ± 0.17s calculate the value for g and the value for uncertainty in g. Using the formula provided in image.
Refer to the Worksheet shown, set up to calculate the displacement of a spring. Hooke's law states that the force (F, in newtons) applied to a spring is equal to the stiffness of the spring (k, in newtons per meter) times the displacement {x, in meters): F= kx. ;Chapter 10, Problem 161CA, Refer to the Worksheet shown, set up to calculate the displacement of a spring. Hooke's law states Cell A3 contains a data validation list of springs. The stiffness (cell 83) and maximum displacement (cell C3) values are found using a VLOOKUP function linked to the table shown at the right side of the worksheet. These data are then used to determine the displacement of the spring at various mass values. A warning is issued if the displacement determined is greater than the maximum displacement for the spring. Use this information to determine the answers to the following questions. Write the expression, in Excel notation, that you would type into cell 86 to determine the displacement of the spring.…
the answer must be: [(13/6)m + (11/9r2)] (double dot) x + (11/9)cẋ + (10/3)kx
Answer the following questions based on scaling arguments, i.e., by applying “the variable X must be proportional to the Zth power of variable Y because of some relevant physical principle”-type reasoning. A. In a surface passivation process for Si wafers, the required processing time to create a 0.1 micron thick SiO2 layer on a pure Si wafer was 2 hours. Estimate the process time required to create an SiO2 layer of thickness 0.15 microns on a pure Si wafer under identical processing conditions. B. A puddle of volatile liquid of initial thickness of 1 cm was found to evaporate to form a thinner 0.5 cm layer in 1 day. How much longer would it take for the liquid layer to evaporate completely?