Engineering drawing 7. Fill-up the blanks in the following sentences by appropriate words selected fromthe list of words given below:(a) Two types of dimensions needed on a drawing aredimensions.and(b) The two systems of placing dimensions aresystem, the dimension is placedbut clear of dimension line.and(c) Into and near the(d) Infrom thesystem, all dimensions are so placed that they are readableedge of the drawing sheet. Dimension lines arenear the middle for inserting dimensions.(e) As far as possible dimensions should be given in one unit, preferably in(f) Dimension lines should be drawn at least 8 mm away from theand from(g) An(h) Mutualorshould never be used as a dimension line.of dimension lines and dimensioning betweenshould be avoided.All dimensions are shown from a common base line in()(i)dimensioning.dimensioning, dimensions are arranged in a straight line, anddimension is placed outside the small dimensions.(k) When a number of parallel dimensions are to be shown near each other,Inänthe dimensions should be(1) The extension line should extend about 3 mm beyond the(m) The line connecting a view to a note is called a(n) The dimension indicating a diameter should beby the symbol(0) The symbolradius.should beby the dimension indicating a(p) Dimensions of cylindrical parts should as far as possible be shown in theviews in which they are seen as(q) Dimension of a cylinder should never be given as a(r) The taper on a shaft is indicated along the(s) The specified length for taper is measured along theof a flat piece and along the(t) The section lines are continuousin casein case of a shaft.lines and are drawn at anofto the main outline of the section.50 Engineering Drawing[Ch. 3List of words for Ex. 7:1. Thin2. Axis9. Crossing17. Millimetres18. Overall25. Leader10. Dimension line26. Radius3. Aligned4. Broken5. Base line6. Bottom7. Centre line8. Continuous11. Dashed line19. Outlines27. Angle12. Each other20. Outline28. R13. Followed29. 4521. Perpendicular22. Progressive23. Rectangles24. Preceded14. Location30. Size15. Middle31. Staggered32. Unidirectional.16. Ø

Answered: Image /qna-images/answer/7f8e131f-3837-4de7-a8ac-05d5fce390f6.jpg

7. Fill-up the blanks in the following sentences by appropriate words selected from the list of words given below: (a) Two types of dimensions needed on a drawing are dimensions. (b) The two systems of placing dimensions are (c) In and and system, the dimension is placed. but clear of dimension line. to and near the (d) In from the system, all dimensions are so placed that they are readable edge of the drawing sheet. Dimension lines are near the middle for inserting dimensions.

7. Fill-up the blanks in the following sentences by appropriate words selected from the list of words given below: (a) Two types of dimensions needed on a drawing are dimensions. (b) The two systems of placing dimensions are (c) In and and system, the dimension is placed. but clear of dimension line. to and near the (d) In from the system, all dimensions are so placed that they are readable edge of the drawing sheet. Dimension lines are near the middle for inserting dimensions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the three appropriate orthographic projections. PLEASE add appropriate dimensions! Use isometric grid paper provided.
Dimensions: a. Can be placed only in model space b. Can be placed only in paper space c. Must be erased and redrawn if the model changes d. Are controlled by their associated dimension style
I would like to draw the three elevations with their dimensions in detail, and these are the existing dimensions. I wish to draw them
P.S: answer the question and plot 4 separate graphs
A 5 cm line segment makes an angle of 30 degrees with the vertical in space. It appears in true size in the front view of a multiview drawing. To plot this line in isometric projection, one needs to layout which lengths and along which isometric axes? a. 5 cos 30 cm along the width axis, and 5 sin 30 cm along the depth axis. b.5 cos 30 cm along the height axis, and 5 sin 30 cm along the width axis. c.5 cos 30 cm along the width axis, and 5 sin 30 cm along the height axis.
Based on the following orthographic projections for each object, generate a full-scale isometric drawing.
Determine if the following sketch is Over Defined, Under Defined, Fully Defined.
Kindly solve this using Primary Dimensions. Thank you very much
Are the location dimensions in Question 4 placed using base line or chain dimensioning?
draw the orthographic projection of given diagram with proper dimensioning
The entire top surface on the part below must be flat within 0.5 but each 25x25 patch must be flat within 0.1. Apply the necessary geometric controls to achieve this result. Please refer to the attached image.
9. show complete STEP BY STEP solution, and draw a FBD.