7. The rotor of a turbine installed in a boat with its axis along the longitudinal axis of the boat makes 1500 rp.m. clockwise when viewed from the stern. The rotor has a mass of 750 kg and a radius of gyration of 300 mm. If at an instant, the boat pitches in the longitudinal vertical plane so that the bow rises from the horizontal plane with an angular velocity of I rad/s, determine the torque acting on the boat and the dircction in which it tends to turn the boat at the instant. [Ans. 10.6 kN-m]

7. The rotor of a turbine installed in a boat with its axis along the longitudinal axis of the boat makes 1500 rp.m. clockwise when viewed from the stern. The rotor has a mass of 750 kg and a radius of gyration of 300 mm. If at an instant, the boat pitches in the longitudinal vertical plane so that the bow rises from the horizontal plane with an angular velocity of I rad/s, determine the torque acting on the boat and the dircction in which it tends to turn the boat at the instant. [Ans. 10.6 kN-m]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The turning-moment diagram for an engine consists of two isosceles triangles each with a height equivalent to a torque of 16kNm. The bases of the triangles lie between ? = 0 ? and ? = 180 , and ? = 180? and ? = 360? respectively. If the engine is to rotate with a mean speed of 130 rpm, calculate the following: the mass of the flywheel having a radius of gyration 1.1m to restrict the fluctuation of speed to +1.5% of the mean speed.
The electric motor exerts a 500-N·m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys B and C are as shown. Take a = 1.4 m, b = 1 m, and G = 27 GPa. Determine the angle of twist between B and C. The angle of twist between B and C is _____ °.
The turning-moment diagram for an engine consists of two isosceles triangles each with a height equivalent to a torque of 16kNm. The bases of the triangles lie between ? = 0 ? and ? = 180? , and ? = 180? and ? = 360? Sketch the turning-moment diagram and add the mean torque line. If the engine is to rotate with a mean speed of 130 rpm, calculate the following: the power developed the mass of the flywheel having a radius of gyration 1.1m to restrict the fluctuation of speed to +1.5% of the mean speed. Demonstrate which would be most effective to reduce the fluctuation of speed, a change in diameter of or a change in mass of the flywheel.
A gear engine automobile is traveling along a curved track of 120m radius. Each of the four wheels has a moment of inertia of 2.3 kg m2 and an effective diameter of 600 mm. The rotating parts of the engine have a moment of inertia of1.25kg m2 the gear ratio of the engine to back wheel is 3:2.The engine axis is parallel to the gear axle and the crank shaft rotates in the same sense as the road wheels. The mass of the vehicle is 2050 kg and the center of mass is 520 mm above the road level. The width by the track is 1.6m, what will be the limiting speed of the vehicle if all the four wheels maintain contact with the road surface (b) Explain the function of a flywheel from a crank effort diagram.
Question No. 18: (a) In an epicyclic gear train, an arm carries two gears A and B having 36 and 45 teeth respectively. If the arm rotates at 150 r.p.m in the anticlockwise direction about the centre of the gear A which is fixed, determine the speed of gear B. If the gear A instead of being fixed, makes 300 r.p.m in the clockwise direction, what will be the speed of gear B? (b) Prove that the resultant unbalanced force is minimum when half of the reciprocating masses are balanced by rotating masses.
A shaft carries four masses, B, C, and D of magnitude 200 kg, 300 kg, 400 kg, and 200 kg respectively and revolving at radii 80 mm, 70 mm, 60 mm, and 80 mm in planes measured from A at 300 mm, 400 mm and 700 mm. The angles between the cranks measured anticlockwise are A to B 45º, B to C 70º, and C to D 120º. the balancing masses are to be placed in planes X and Y. The distance between the planes A and X is 100 mm, between X and Y is 400 mm and between Y and D is 200 mm. If the balancing masses revolve at a radius of 100 mm, find their magnitude and angular positions.
An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number. An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number.
Suppose an automobile engine can produce 195 N⋅m of torque, and assume this car is suspended so that the wheels can turn freely. Each wheel acts like a 14 kg disk that has a 0.195 m radius. The tires act like 2.15-kg rings that have inside radii of 0.18 m and outside radii of 0.34 m. The tread of each tire acts like a 8.5-kg hoop of radius 0.335 m. The 16-kg axle acts like a solid cylinder that has a 1.75-cm radius. The 29.5-kg drive shaft acts like a solid cylinder that has a 3.25-cm radius. Calculate the angular acceleration, in radians per squared second, produced by the motor if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car.
A single cylinder horizontal engine runs at 120 r.p.m. The length of stroke is 400 mm. The mass of the revolving parts assumed concentrated at the crank pin is 100 kg and mass of the reciprocating parts is 150 kg. Determine the magnitude of the balancing mass required to be placed opposite to the crank at a radius of 150mm which is equivalent to all the revolving and 2/3rd of the reciprocat- ing masses. If the crank turns 30° from the inner dead centre, find the magnitude of the unbalanced force due to the balancing mass.
A shaft is rotating at a uniform angular speed. Four masses M1, M2, and M3 and M4 of magnitudes 300kg, 450kg, 360kg, 390kg respectively are attached rigidly to the shaft. The masses are rotating in the same plane. The corresponding radii of rotation are 200mm, 150mm, 250mmand 300mm respectively. The angle made by these masses with horizontal are 0°.45°, 120°and 255°respectively. Find-(i) the magnitude of balancing mass (ii) the position of balancing mass if its radius of rotation is 200mm.
Need answer ASAP.Inside a machine, two gears, A and B, HINGED at their centers, are meshed with each other such that gear A transmits torque and speed to gear B. Gear A has a mass mA=2 kg, radius rA=175 mm, and radius of gyration kA=150 mm. Gear B has a mass B=5 kg, radius rB=525 mm, and radius of gyration kB=400 mm. From rest, a counter-clockwise couple M of constant magnitude 6 Nm is applied to Gear A. Which of the following diagrams CORRECTLY describes a force-inertia diagram used to solve the problem? What is the relationship between the angular accelerations of gears A and B?
A locomotive consists of multi cylinder reciprocating engine running at a speed of 8 r.p.s having a stroke length of 29cm, which carries a mass of reciprocating part whose magnitude is 11kgs with a revolving part of 5kgs rotating at 17cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 500 from top dead centre to bottom dead centre. solve 4 and 5 1. Maximum primary unbalanced force of reciprocating mass in newtons 2. Balancing mass required at a radius of 41cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 76cm between the two cylinders in (N-m) 5. Magnitude…