7.a. Which of the following types of grounding system should be installed in a patient care area? A. Surge absorbing B. Redundant C. Exothermically bonded D. Isolated 7.b. Isolated power systems installed in healthcare facilities are required to A. be grounded. B. have an equipotential plane. C. operate as a separately derived system. D. operate ungrounded.

7.a. Which of the following types of grounding system should be installed in a patient care area? A. Surge absorbing B. Redundant C. Exothermically bonded D. Isolated 7.b. Isolated power systems installed in healthcare facilities are required to A. be grounded. B. have an equipotential plane. C. operate as a separately derived system. D. operate ungrounded.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.19MCQ

See similar textbooks

Similar questions

Construct a complete electrical plan layout of a residential type building which includes floor plans, lighting layout, power layout and load schedule.
A bolted line to line short circuit is used to determine the thermal withstand rating of the cables and the breaking capacity setting of a circuit breaker Select one: True False
4. What can installation records be used to determine while servicing equipment?A. Broken connectors in a cable linkB. Problems due to aging during operationC. Broken fiberD. Decreased bending radius during operation
A cable TV company was interested in making its operation more efficient by cutting down on the distance between service calls while still maintaining at least the same level of service quality. A treatment group of 18 repairpersons was assigned to a dispatcher who monitored all the incoming requests for cable repairs and then provided a service strategy for that day’s work orders. A control group of 18 repairpersons was to perform their work in a normal fashion—that is, by providing service in roughly a sequential order as requests for repairs were received. The average daily mileages for the 36 repairpersons are recorded in the table below. a. What are the populations of interest in this study?b. What is the level of significance of your test?c. Is there significant evidence that the treatment group had a smaller average daily mileage than the control group? Use α = 0.05
A three-phase, three wire, CBA system with a line voltage of 120 Volt, has three impedances of 30 /60ᴼ in Deltaconnection. Assume that VCA is the reference vector. Determine the line current and draw the voltage-currentphasor diagram.
A telephone company operates three identical stations at differentlocations. During one-year period, the number of malfunctions reported byeach station and the causes are shown below. (a)Suppose that a malfunction was reported and it was found to be caused byother human errors. What is the probability that it came from station C (b) If a malfunction was reported because of computer malfunction, whichstation is most likely reported the malfunction?
24. In Single Busbar System with Bus Sectionalization, any two sections of the Busbar are connected via Circuit Breaker and Isolators. Select one: True False
The base current and base voltage of a 345 kV system are chosen to be 3000A and300kV respectively. Determine the base impedance and the per-unit voltage for thesystem.
recommended the testing of wiring installations for domestic load
Preference setting is used for controlling what parameter of a generating system and who will take care of this setting? ..
4.a. An intersystem bonding termination will typically be used as a ground junction for a/anA. patient care area.B. communications system installation.C. fire protection system.D. information technology room.4.b. The supply systems for sensitive electronic equipment are _______ systems.A. four-wire, three-phaseB. three-wire, single-phaseC. three-wire, three-phaseD. four-wire, single-phase
5. Identify the minimum distance requirements between network cables and power sources and identify types and location for cable supports.