(8) A steel shaft transmits 30kW @ 1,400rpm. Considering allowable shearing stress based on pure torsion to be 35,000kPa, find: (a) the shaft diameter; (b) the torsional deflection of the shaft per unit length, use G = 83GPa.

(8) A steel shaft transmits 30kW @ 1,400rpm. Considering allowable shearing stress based on pure torsion to be 35,000kPa, find: (a) the shaft diameter; (b) the torsional deflection of the shaft per unit length, use G = 83GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.15P: A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner...

See similar textbooks

Related questions

Q: Given the multiview projection of the solid, draw the isometric view.

A: According to the details provided in the question, we need to draw an isometric view. 1. I am using…

Q: A 3 m3 air tank has an initial pressure of 120 kpa and 35oC. The heat is added until its pressure…

Q: 4) A sophisticated machinery design has a flat bar fillet component with a thickness of 10mm. For an…

Q: Determine the minimum allowable indoor temperature that will ensure a humidity control system…

A: ASHRAE is basically an American national standard body that publishes the standard related to air…

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

Q: A gas within a piston-cylinder assembly executes a Carnot power cycle during which the isothermal…

A: As per bartleby guidelines we are allowed to solve only 1st 3 subparts if multiple subparts are…

Q: Consider a cycle which uses a pump to increase the pressure of liquid water from a lake by AP = 4…

Q: b) Calculate the inclined angle λ and orthogonal rake angle yo, when yx =10°, yy =8°, ps=15°.

Q: W.S (t=0) 13. In Fig. H is shown a tank 1.5 by 1.5m horizontal section and 3m high with two orifices…

Q: A mixture of water (density=1000 kg/m3) and vapor flowing with a mass rate = 7 kg/sec in a pipe of…

A: Given: mass fraction of the gas=20%: Hence mass fraction of the water=100-20=80% Because mass flow…

Q: Envision a solar water heater, a device which receives energy from the sun (solar radiation or…

Q: A car starts from rest at point O on a circular track with a radius of r = 350 m. The speed of the…

Q: Which methods will be employed to find the frequency of oscillations?

A: Simple harmonic motion is a form of periodic motion in mechanics and physics in which the…

Q: A smooth pipe flow has a turbine installed between two different size pipes, where d1 = 2.2 cm and…

Q: You designed a z-axis acceleration sensor with a proof mass of 0.2 um thick and 20 um by 30 um…

A: Analog and digital sensors are the two types of sensors that may be categorised. Temperature…

Q: Determine the force required to produce stress of 2 N/mm2 if cross sectional area is 2 mm2

A: Given data : Cross sectional area=A Stress=σ Required : Force

Q: Calculate the polar moment of inertia of the shaded area about point O.

Q: Fill in all blanks before submission. Round the answer to the nearest integer. The post shown below…

A: Apply Equilibrium Conditions

Q: uare thread N. The screw and a pitch

Q: A rectangular plate 0-5 m long, 0.1m wide and 6 mm thick is clamped at the edges. It carries a udl…

A: The given rectangular plate and the udl is as shown below, Calculate the udl value, Intensity=1.5…

Q: do you think that all of the stipulations in the Code of Ethics for Mechanical Engineers are still…

A: To Find :- Is all of the stipulations in the Code of Ethics for Mechanical Engineers are still…

Q: A fluid is flowing through two different tubes of same cross-section area. We are to compare the…

A: Given: The length of the circular pipe and square pipe is same. Heat transfer is calculated as:…

Q: Find the density of liquid whose specific gravity is 1.45

A: Given data : Specific gravity=S.G Density of water=ρW Required : Density of liquid

Q: The most influencing parameter on Reynold number is: choose one 1-Fluid density 2-Fluid velocity…

A: This question is based on the concept of Reynolds number

Q: A fluid is flowing in a smooth pipe (inside diameter = 40 mm) with a welocity of 10 m/sec, the fluid…

A: Ans: f= 0.025

Q: quare thread power scr KN. The screw has a me and a pitch of 6 mm. T Fiction and collar frictio

Q: lanet if the satellit in a circular orbit the planet. (See inf

Q: ure 30° РА Ꮎ 1 of

Q: b) Calculate the inclined angle λ and orthogonal rake angle yo, when yx =10°, yy =8°, qs=15°.

Q: 28. The life of a bearing supporting a rotating shaft is expressed in number of revolutions. Compute…

Q: If you had a fixed mass of hot air stored in a rigid container and decided to transfer heat from the…

Q: A mixture of water (density=1000 kg/m3) and vapor flowing with a mass rate = 7 kg/sec in a pipe of…

Q: Figure Q3 shows a hydraulic cylinder made of AISI 1050 CD material under external loading and…

A: Given that, Diameter, d=250 mm,Thickness, t=80 mm,Material AISI 1050 CD steel,Ultimate tensile…

Q: Summarise the applications of Additive Manufacturing & 3D Printing (AM3DP) and discuss the impacts…

Q: Determine the forces in members CD, CJ, and DJ. 6 panels at 3¹ M K H A L B L C A₂ Answer: ly = i D E…

Q: (11) A 120cm diameter diamond circular blade, mounted on a pulley-driven steel shaft, is requiring a…

A: Given data, Diameter of the diamond blade, D = 120 cm = 1.2 m Peripheral linear speed of the blade,…

Q: Given data: U=2 m/s V=2.8 m/s t=0.3 s Find acceleration

A: Given data : Initial velocity=U Final velocity=V Time=t Required : Acceleration

Q: At an altitude of 1,600m, the atmospheric pressure is 81.49kPa. What is the specific humidity and…

A: Write the given data. P=81.49 kPatwb=5°Ctdb=10°C Here, P is the total pressure, tdb is the…

Q: YES OR NO. DO BOTH THE ORTHOGRAPHIC MATCH EACH OF THE ISOMETRIC

A: ORTHOGRAPHIC MATCH EACH OF THE ISOMETRIC

Q: 3- Consider a cogeneration power plant modified with regeneration. Steam enters the turbine at 6 MPa…

Q: a reservoir. Expr the stream at poir les of the velocitie

A: solution of above problem is below:

Q: Q2/ A full journal bearing has a nominal diameter of 80mm, a bearing length of 20mm and support a…

Q: 20. The density of fuel having 28° Baume is A. 0.886 B. 0.871 C. 0.893 D. 0.654

Q: 8.13 Determine the load carrying capacity of a hook of rectangular cross-section. The thickness of…

A: The weight carrying capacity of a hook with a rectangular cross-section must be determined.We know…

Q: Answer this ASAP plz A double row angular contact ball bearing is used in the engine compressor to…

Q: A fluid is flowing in a smooth pipe (inside diameter = 40 mm) with a velocity of 10 m/sec, the fluid…

A: The Reynolds number of the flow can be determined as shown below.

Q: Initially saturated water liquid at 200°C is contained in a piston-cylinder. The water is then…

Q: Air is flowing in a duct with velocity of 7.62 m/s and static pressure of 2.16 cm water gage. The…

Q: Water at 10°C is is flowing at 0.8 m/s across a long cylinder that is made of a material that…

Q: Determine the values of VT for temperatures of 40C.

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A stepped shaft consisting of solid circular segments having diameters D1= 2.0 in, and D2= 2.4 in. (see figure) is subjected to torques T. The radius of the fillet is R = 0,1 in. If the allowable shear stress at the stress concentration is 6000 psi, what is the maximum permissible torque Tmax?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A thin-walled steel tube having an elliptical cross section with constant thickness t (see figure) is subjected to a torque T = 18 kip-in. Determine the shear stress and the rate of twist in degrees per inch) if G = 12 × 106 psi, t = 0.2 in., a = 3 in., and b = 2 in. Note: See Appendix E, Case 16, for the properties of an ellipse.
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (see figure), (a) If the allowable shear stress in the shaft is 43 MPa, what is the maximum torque (T0)max that may be applied at section C? (b) Find (ï^),^ if the maximum angle of twist is limited to 1.85', Let G = 28 GPa.