8) Chapter 3: Problem 3.21: One of the inspectors in the quality control department has frequently used the Brinell and Rockwell hardness tests, for which equipment is available in the company. He claims that the Rockwell hardness test is based on the same principle as the Brinell test, which is that hardness is measured as the applied load divided by the area of the impression made by an indentor. Is he correct? If not, how is the Rockwell test different?

8) Chapter 3: Problem 3.21: One of the inspectors in the quality control department has frequently used the Brinell and Rockwell hardness tests, for which equipment is available in the company. He claims that the Rockwell hardness test is based on the same principle as the Brinell test, which is that hardness is measured as the applied load divided by the area of the impression made by an indentor. Is he correct? If not, how is the Rockwell test different?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In your summer internship, you are tasked with measuring the ultimate tensile strength of a material to determine if it meets your company’s (Superior Super Ships Inc) specification. Your boss is worried that the new low-cost supplier, Shoddy Alloys Inc, may not be reliable but it is the only way to source on-time the SS304 needed to make finishings for Jeff Bezos’ new yacht, the Black Pearl. You collect several load versus displacement curves, as illustrated below. The initial diameter of the round gauge section is 0.25 in. You also collect the instantaneous diameter of the specimen during the test using a laser. Using the provided data, calculate what is the ultimate tensile strength measured in this test?
In the First project: you have been asked to perform tensile testing for four different materialsand analyse the results and work on some NDT process selection:a. For the results shown in Table 1 of the tensile testing that you have performed, find thefollowing, if you know that the original length of specimen is 20.8 mm and the original diameteris 6.4 mm. Fill the calculated results in the summary table below (Table 1):1. Plot the engineering stress versus engineering strain for each material and L-D Diagram.2. Compute the modulus of elasticity, E in GPa.3. Determine the yield strength at a strain offset of 0.002.4. Determine the tensile strength in MPa.5. What is the approximate %El ductility, measured by percent elongation?6. Compute the modulus of resilience.7. Determine the fracture stress in MPa.8. Compute the final area (Af) in mm2.
In a tensile test, initial length of the experimental specimen is ____________ the final length of the specimen.
Tensile test is a method to investigate the elasticity of a material. A test specimen is placed between two clamps and these clamps will move in opposite directions, hence straining the test specimen. This experiment will yield a stress-strain curve that shows each of the stages of the specimen for every load is applied. With an aid of sketching diagrams, describe the stages that the specimen experiences before it breaks, and relate it with the stress-strain curve. It is expected that each stage comes with a sketching of the specimen and explanation of the current stage.
part 1 When the material enters the _____ region of the stress-strain curve, the material is no longer able to go back to its original shape and is _____ deformed. Plastic, permanently Elastic, temporarily Elastic, permanently Plastic, temporarily
The stress and a pipe varies jointly with the internal pressure and the diameter of the pipe, and inversely with the square of the thickness of the pipe. The stress is 200 pounds per square inch when the diameter is 4 inches, the thickness is 0.40 inches, and the internal pressure is 25 pounds per square inch. Find distressed wood and internal pressure is 50 pounds per square inch if the diameter is 10 inches and a thickness is 0.50 inches. Define variables Stress in pipe Internal pressure of pipe Diameter of pipe Thickness of pipe Find k Update formula Answer question
An experiment to determine the effect of four different types of engine oil (A, B, C, and D) on the rolling friction coefficient of a car speed has been conducted. Three brands of car (Honda, Toyota, and Mazda) were chosen, and each engine oil was tested twice on each car, producing the following ANOVA output in Figure 2. i) How many treatments involved? Write down all the treatments.ii) Identify the number of replication for each treatment. iii) Based on the ANOVA table above, find the values of W, X, Y and Z. iv) Test the interaction effect on rolling friction coefficient of car speed between the four different types of engine oil and the three different brands of car. v) Do we need to test for marginal effect? Give a reason.
5b.You used a material to design a system. The more you apply external force, the more the system becomes rigid. Use a sketch to explain how the material is disobeying the stress and strain characteristics. Give two(2) examples.
Porosity is a measure of the void or empty spaces in a material and is a fraction of the volume of voids over the total volume. The density of the solid material used to create 10 pieces of 1.05 cm diameter and 1.31 cm height cylindrical beads is determined to be 1.53 g/mL. These beads were then placed in a flask and was filled to the 36 mL mark with a salt solution. The total weight measured of the beads and the salt solution was 47.86 g. Upon further inspection, it was found that manufacturing defects caused the measured porosity of the beads to be at 29%. Assuming that the solution was able to fully fill the empty spaces inside the beads, calculate the density of the salt solution. Show your solutions in the next item (Kindly use GRESA, thank you) Round your answer to 2 decimal places.
Between 1. Nominal (engineering) stress and true stress and 2. True strain and engineering strain which is always less than the other?
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 143 kN. - Length of the specimen is 29 mm. - The yield strength is 71 kN/mm2. - The percentage of elongation is 48 %. Determine the following Diameter of the specimen, Final length of the specimen, Stress under an elastic load of 18 kN, Young's Modulus if the elongation is 1 mm at 18 kN and Final diameter if the percentage of reduction in area is 29 %. Initial Cross-sectional Area 2.01 mm2. The Diameter of the Specimen 1.59 mm. Final Length of the Specimen 42.92 mm. Stress at the elastic load 8955.22 N/mm2. Find: Young's Modulus of the Specimen (in N/mm2) Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm)
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 143 kN. - Length of the specimen is 29 mm. - The yield strength is 71 kN/mm2. - The percentage of elongation is 48 %. Determine the following Diameter of the specimen, Final length of the specimen, Stress under an elastic load of 18 kN, Young's Modulus if the elongation is 1 mm at 18 kN and Final diameter if the percentage of reduction in area is 29 %. FIND: Young's Modulus of the Specimen (in N/mm2) Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm)