8. In the figure, a setup for testing an adhesive is prepared. For this, a rubber 15 kN block was taken and rigid metal sheets were attached to this block. Adhesive 15 kN as it leaves when force is applied in its severity; 40 15 KN a) The shear strength of the adhesive, b) Find the warping angle in the block at the time of break ( G = 0.4 GPa) Dimensions are in mm.

8. In the figure, a setup for testing an adhesive is prepared. For this, a rubber 15 kN block was taken and rigid metal sheets were attached to this block. Adhesive 15 kN as it leaves when force is applied in its severity; 40 15 KN a) The shear strength of the adhesive, b) Find the warping angle in the block at the time of break ( G = 0.4 GPa) Dimensions are in mm.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.12P: Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in...

See similar textbooks

Similar questions

Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
A plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of the bars is 80. If the allowable shear strain in the plastic is 0.014 radian, what is the minimum permissible length of the bar in mm?
In lab tests on a brick whose dimension are shown in the figure to the right, a force of 1500 N directed at 9.00º above the horizontal is applied on both the lower and upper faces of the brick causing the vertical side of the brick to deform through an angle of 1.25º. (a) How much shear stress is applied on the upper and bottom surfaces of brick? (b) What is the shear modulus of the brick?
If the shear stress in a material is 20 MPa and the corresponding shear strain is 0.0005, calculate the shear modulus of the material.
Question 1: Taking the safety factor as 2 for the loading condition shown in the figure, we can calculate the maximum axial force (P) that can be applied. d=100mma) On the theory of maximum normal stressb) Maximum shear stress theoryc) Calculate according to the maximum strain energy theory.The structure is made of steel and the proportional limit is 250 MN / m2 in pressing and drawing, and 140 MN / m2 in shear. The elasticity module of the material is 200 GPa and the Poisson's ratio is 0.3. d=100mm
I can't seem to find the shear stress at point b. Here's my work for reference.
In the wood industries, inclined blocks of wood are sometimes used to determine the compression-shear strength of glued joints. Consider the pair of glued blocks A and B in Figure 4 which are 38 mm deep in a direction perpendicular to the plane of the paper. Determine the shearing ultimate strength of the glue in MPa if a vertical force of 50 kN is required to cause rupture of the joint.
A rod of length 20 mm is stretched to make a rod of length 40 mm. Subsequently it is compressed to make a rod of final length 10 mm Consider the longitudinal tensile strain as positive and compressive strain as negative.What is the total true longitudinal strain in the rod?
An aluminum wire of length 2.0 m and diameter 5 mm is used to hang a load of 100 kg. The modulus of elasticity of aluminum is 65 GPa and consider a Poisson’s ratio of 0.30. a) Calculate the final length of the wire when the load is applied. b) Calculate the final diameter of the wire when the load is applied. (round off your answer in 5 decimal places).
The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel (ρsteel=7900kg/m3)(ρsteel=7900kg/m3). The sides are made of 0.550 cmcm -thick steel. To do this problem, assume that the bottom of the boat is the full dimensions, but that the sides of the boat are welded onto the top of the bottom (so the total side height is the height of the side plus the thickness of the bottom). h= ? cm
A block of wood is tested in direct shear using the loading frame and test specimen shown in the figure. The load P produces shear in the specimen along plane AB. The height “h” of plane AB is 50 mm and its width (perpendicular to the plane of drawing) is 100 mm. If the load P = 16 kN, what is the average shear stress in the wood? Express the answer in MPa. why some answers are 6.40mpa and others are 3.2mpa? im confused
A rectangular bar is notched on two sides as shown in Fig. 5.9a. The dimensions of the bar are thickness t = 0.2 cm, D = 2 cm, d = 1.8 cm, h = 0.1 cm, and r = 0.15 cm. If an elastic load of 15 kN is applied along the axis of the bar, what is the maximum stress in the vicinity of the notches? If the yield strength of the material is 950 MPa, will the material yield near the notches under this load?