The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel (ρsteel=7900kg/m3)(ρsteel=7900kg/m3). The sides are made of 0.550 cmcm -thick steel. To do this problem, assume that the bottom of the boat is the full dimensions, but that the sides of the boat are welded onto the top of the bottom (so the total side height is the height of the side plus the thickness of the bottom). h= ? cm

The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel (ρsteel=7900kg/m3)(ρsteel=7900kg/m3). The sides are made of 0.550 cmcm -thick steel. To do this problem, assume that the bottom of the boat is the full dimensions, but that the sides of the boat are welded onto the top of the bottom (so the total side height is the height of the side plus the thickness of the bottom). h= ? cm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.10P: A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in...

See similar textbooks

Similar questions

A copper and steel wires are welded together at their ends. The original length of each is 50 cm with the total length of 100cm and each has a diameter of 0.78 mm. A mass of 10 kg is suspended from the combined wire. By how much will the combination stretch? Ycopper=100 GPa, Ysteel= 210 GPa.
Two circular plates with (2d) and (d) as outer and inner diameters respectively, are clamped together by means of a bolt as shown in figure. The bolt is made of plain carbon steel (Sy= 380 MPa and E = 207 GPa), while the plates are made of aluminium (E = 71 GPa) The initial pre-load in the bolt is 3 kN and the external force acting on the bolted joint is 7.5 kN. Determine the size of the bolt from the given table, if the factor of safety is 2.5 and assume coarse threads required.
A 5.0m long steel wire has a cross-sectional area of 0.55cm^2. Its proportional limit has a value of 0.0018 times its Young's modulus. Its breaking stress has a value of 0.0065 times its Young's modulus. The wire is fastened at its upper end and hangs vertically. a. How great a weight can be hung from the wire without exceeding the proportional limit? b. How much will the wire stretch under this load? c. What is the maximum weight that the wire can support?
A cylinder head of a steam engine is held on by 14 bolts. The effective diameter of the cylinder is 35 cm and the steam pressure is 8.5 kg/cm2. Assuming that the bolts are not initially stressed, find the diameter of each of the bolts if the tensile stress is not to exceed 200 kg/cm2.
A disk of SBR elastomer 3.0 cm in diameter 0.5 cmthick is used as a cushioning surface between two steel rods ofthe same diameter, as shown below (not to scale). a. If the rods are brought together with an axial force of 100 N such that the SBR is compressed elastically between them, what is the thickness of the SBR under load? b. Under the same conditions as part (a), what is the greatest possible diameter of the SBR under load? c. If the SBR is bonded to the rods, how far can one rod be rotated with respect to the other before the SBR/rod interface fractures? Assume that the rods are essentially rigid and the distance between them remains constant. Please answer in degrees of rotation.
The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel (ρsteel=7900kg/m3)(ρsteel=7900kg/m3). The sides are made of 0.550 cmcm -thick steel. To do this problem, assume that the bottom of the boat is the full dimensions, but that the sides of the boat are welded onto the top of the bottom (so the total side height is the height of the side plus the thickness of the bottom). Find the h ( cm)
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod are given as 10 mm and 120 mm,respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,00053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Determine : A) Strain in the steel rod B) Load carried by the steel and brass rods C) Modulus of elasticity for the brass
A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter . The internal diameter of the hoop formed by the band is 29.98cm . By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder ? What stress will occur in the hoop when it reaches the same temperature as the cylinder , if the deformation of the cylinder may be neglected ? (Write complete solution)
A steel rod with a cross-sectional area of 180 mm2 is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 10-6 mm/ (mm°C) and E = 200 GPa. Which of the following most nearly gives the temperature at which the compressive stress will be 48 MPa? Which of the following most nearly gives the temperature at which the tensile stress will be 48 MPa? Which of the following most nearly gives the temperature at which the stress will be zero?
A 100 mm x 100 mm x 100 mm cube made with glass polymers in the y- direction is subjected to a tensile load of 100 kN along the y-direction. However, the cube is constrained against deformation in the x and z directions. Given the following properties: Ex = 20 GPa Ey = 50 GPa Ez = 20 GPa vxy = 0.25 vxz = 0.5 vyz = 0.25 (a) Compute for the change in length of the cube in the y-direction and; (b) Determine the stresses, σx, σy, σz
A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a 25∘ angle with the crane (Figure 1). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 m from the upper end of the crane. 1. When the crane is raised to 55∘ above the horizontal holding an 11,000 N pallet of bricks by a 2.2 m very light cord, find the tension in the cable. 2. Find the horizontal component of the force that the axle exerts on the crane.
[Please Write Clean and Provide Complete Explanation] One end of a 2 m long steel rod (d = 3 cm) is rigidly attached to a wall so that the rod is perpendicular to the wall. The other end of the rod is welded to a second rod, which is 1 m long (d = 1.0 cm). The second rod is parallel to the wall and the floor. A vertical force of 50 N is applied to the end of the second rod. For both rods, the modulus of elasticity is 210 × 109 Pa and the shear modulus is 79 × 10 9 Pa. There is an infinitesimally small cubic element at the top surface of the 3 cm diameter rod immediately adjacent to the wall, that is, at (0, 1.5, 0). What is most nearly the maximum normal stress due to the bending moment?