8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal. Determine the conducting and transformed currents of auto transformer. A N1=200 NBc=20 N2=100 NBA=30 10A 200 V 50,Hz N1 : N2 lellll

8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal. Determine the conducting and transformed currents of auto transformer. A N1=200 NBc=20 N2=100 NBA=30 10A 200 V 50,Hz N1 : N2 lellll

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.63P: A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a...

See similar textbooks

Related questions

Q: A 10 kVA, 2400/240 V, 60 Hz single phase transformer has Z, = 5.2 + j12.5 ohms and Z2 = 0.06 + j0.12…

A: In this question, We need to calculate the load voltage if Primary voltage and frequency is rated.…

Q: Excitation arm parameters of 1000V/400V single phase transformer with 15kVA power: Xm = 6kΩ an Given…

A: Given ;1000/400 V1-ϕ transformer with a power 15KVA,Xeq=6 K ohm Re=20 Kohm a)Electrical equivalent…

Q: A 400-kVA transformer has a primary winding resistance of 192 and a secondary winding resistance of…

A: Transformer is a static electrical device which transfers power from one circuit to another circuit…

Q: A 4 MVA, 66/13.2 Kv, 50 Hz. Delta star connected Three phase transformer has a primary resistance…

A: The current flowing in a circuit causes a voltage drop. The voltage drop should be within allowable…

Q: QS A 20KUA , 200/Soo usit single phax step-uptransformer Ras: primary resistanue 3.0.02 23 secondany…

A: The data for the question are: 20kVA, 200/500V,R1=0.02Ω,R2=0.04Ω,Ro=1000Ω,Xo=750Ω The magnetizing…

Q: The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.…

A: In this question, Both transformers are ideal so no losses. We know in transformer I1/I2= N2/N1

Q: A 2000-kVA, 6,600/400-V, 3-phase transformer is delta-connected on the high voltage side and…

A: Given Data: Transformer rating : 2000-kVA, 6,600/400-V, 3-phase Full load pf = 0.8 Short circuit…

Q: Q2) A 140-kVA, 7500/277-V distribution transformer has the following resistances and reactances: R,…

A: As per the guidelines of Bartley we supposed to answer first three subpart only.

Q: A 2000-kVA, 6,600/400-V, 3-phase transformer is delta-connected on the high Example voltage side and…

Q: For an iron core transformer shown in Figure, the net cross sectional area of the core is 100cm2. If…

A: Given parameters N p=75 Ns = 200 V1 =230V Frequency f =50Hz 1. Turn ratio =Np/Ns=75/200=0.375

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

Q: A 1000-VA 380 / 110 V conventional transformer is to be used to supply power from a 490-V source to…

A: From the given data of normal transformer, KVA=1000 VAVP=380 VVS=110 V To the Auto-transformer…

Q: b) A 20kVA 8000/277V distribution transformer has the following resistances and reactances: Rp = 320…

A: This question is related to single phase transformers

Q: 8- In core design of power transformer the number of steps increased as the cross-sectional area…

A: In core designing of the power tramsformer, the number of steps are more as the cross section area…

Q: A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and…

Q: 1. The equivalent circuit impedances of a 20-kVA, 800CV240-V, 60-Hz transformer are to be…

A: Since we are allowed to solve only the first question, The below solution contains answer for the…

Q: 10 A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and…

A: In this question we need to find a type of winding connected in LV side.

Q: An ideal transformer is connected to a voltage source given by es(t) = 100cos(2000nt)V on the…

A: In this question, Ideal transformer is connected to the es = 100cos(2000πt) V. Transformer turn…

Q: In no-load mode a single phase two windings power transformer draws apparent power S10=100VA at…

Q: Q.2 (a) Give TWO reasons why we must use transformer in electrical system. (b) A single-phase…

A: a) To reduce transmission line losses, transformers are utilised to boost up the input voltage.…

Q: QI An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load…

A: Given data: Core loss = 1.4 kW Full load Copper loss= 1.6 kW Full load KVA =150 Power factor…

Q: An ideal transformer with N, = 2400 and N2 = 400 is connected with an impedance Z2 across winding 2,…

A: In this question, We need to determine the impedance Z2 " Referred to primary side? We know…

Q: The primary of a certain transformer takes 1 A at a power factor of 0.4 when connected across a 230…

Q: 8.(a) A 100 KVA, 50 Hz, 440/11000 V, 1-phase transformer has an efficiency of 98.5% when supplying…

A: Let Pi → Iron losses Pl4→Full load copper losses At full load , 0.8 Power factor efficiency=98.5…

Q: A 1000-VA, 230/115-V traformer has been tested to determine its equivalent circuit. The results are…

Q: 8.a. The type of coil usually used in power transformers rated at less than 15,000 volts is the A.…

A: windings surround the core, the transformer is core form Windings are surrounded by the core, the…

Q: transformers and VA) connectéd in parallel as shown in the following figure. %Z1=2% ST1 Zeq1 SL1 SL2…

Q: 8. The two winding transformer and the autotransformer of the circuit shown in Figur Determine the…

A: given transformer and autotransformer

Q: ) A single-phase transformer, with primary turns of 500, is delivering full-load of 80 kW at a…

A: We are authorized to answer three sub part at a time, since you have not mentioned which question…

Q: 3/The core of a 300-kVA, 15000/650 V, 50-Hz, 1-ph, core type transformer has across- section of 30…

A: In the given question we note that The core of = 300 KVA , 1500/ 650 V Cross section area is…

Q: a. The primary of a certain transformer takes 1 A at a power factor of 0.4 when connected across a…

A: (a) Part (i) Consider the transformer is on open-circuit. Draw the circuit diagram of an equivalent…

Q: As given in the figure, an ideal transformer with a 2: 1 winding ratio is fed from a 240 Volt source…

Q: single-phase transformer, with primary turns of 500, is delivering full-load of 80 kW at a lagging…

A: power factor=0.8 logV1=220 V ; N1=500f=50 HzI2=227 APower output=80 KWV2 I2 cos…

Q: A transformer on no-load has a core-loss of 20 W, draws a current of 1 A (rms) and has an induced…

A: According to guidelines we need to solve only the first question. According to the question we have…

Q: A 200 – kVA transformer with impedance of 5 percent and the power factor of the load is 85 percent.…

A: Given, A transformer with KVA rating, S=200 kVA Impedance, Z=5% Power factor, cosϕ=85%=0.85 Primary…

Q: ABB company manufactures 44 kVA, 2200/220 V conventional transformer. Using this transformer, design…

Q: Q.2: The parameters of a 200/3000V, 50Hz single phase transformer are given below: R₁-0.018 02,…

A: It is given that: R1=0.018 ΩX1=0.004 ΩR2=0.018 ΩX2=10 ΩRo=150 ΩXo=800 ΩZL=50-j75 Ω

Q: A transformer has a reactive drop of 6% and a resistive drop of 2.5%. Determine the lagging power…

A: The voltage regulation is given by the expression as shown below: In terms of the values of the…

Q: The core of a 30, 50-Hz, 11000/550-V, A-Y, 300 kVA, core-type transformer operates with a flux of…

A: In this question we will find full load high voltage phase current....

Q: 18. An ideal 50-Hz, core-type transformer has 100 primary-turns and 200 secondary- turns. The…

Q: The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.…

A: Given two winding transformer and the auto transformer of the circuit,

Q: 8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.…

A: given transformer and autotransformer

Q: 5) The maximum efficiency of a 100 kVA, 6600/240 V, 60 Hz single phase transformer occurs at half…

A: The solution is given below

Q: Asiacell|ASIACELL 3G 2G zain IQ BartlebySolutions.. 1 • Q1: During the separation of transformer…

A: Note :- as per our guidelines we are supposed to answer 1 question at a time in case of multiple…

Q: A 15-kVA, 2300/230- Question-2 !* V transformer has the following resistances and leakage…

A: As per the guidelines of Bartley we supposed to answer first three subpart only

Q: The primary ofa certain transformer takes 1 A at a power factor of 0.4 when connected across a 230…

Q: A 1000-VA, 230/115-V transformer has been tested to determine its equivalent cir- cuit. The results…

A: Transformer of 1000 VA,230/115-v Open circuit test(secondary side)Voc=115 vIoc=0.11 APoc=3.9 wShort…

Q: F ← N₂ = 40 t ell Denotes iron-core 1,-100 mA For the iron-core transformer of figure. Find the…

Q: Question 3: Design an isolated transformer to energise Load at the below circuit. The Load power is…

A: Electrical machines can be either generator , transformers or motors. They can be either Ac machines…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.
Determine the conducting and transformed currents of auto transformer.
N1=200 NBC=20
N2=100 NBA=30
10A
200 V
50,Hz
N1 : N2
lell

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An ideal transformer has no real or reactive power loss. (a) True (b) False
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
Consider Figure 3.25 of the text for a transformer with off-nominal turns ratio. (i) The per-unit equivalent circuit shown in part (c) contains an ideal transformer which cannot be accommodated by some computer programs. (a) True (b) False (ii) In the - circuit representation for real c in part (d), the admittance parameters Y11 and Y12 would be unequal. (a) True (b) False (iii) For complex c, can the admittance parameters be synthesized with a passive RLC circuit? (a) Yes (b) No
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.