8.13 (C). At a point in a material a resultant stress of value 14 MN/m² is acting in a direction making angles of 43°, 75° and 50°53' with the coordinate axes X, Y and Z. (a) Find the normal and shear stresses on an oblique plane whose normal makes angles of 67° 13', 30° and 71°34', respectively, with the same coordinate axes.

8.13 (C). At a point in a material a resultant stress of value 14 MN/m² is acting in a direction making angles of 43°, 75° and 50°53' with the coordinate axes X, Y and Z. (a) Find the normal and shear stresses on an oblique plane whose normal makes angles of 67° 13', 30° and 71°34', respectively, with the same coordinate axes.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

A 9 ft wide and infinitely long flexible strip load of 800 lb/ft2 is placed on an elastic medium as shown in Figure P8.7. Find the vertical stress increase at points A, B, and C located 3 ft below the surface.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12.4 ksi, Sy = 3.5 ksi, and Sxy = 3.6 ksi. Assume B = 29°. Determine the normal stresses ox, and oy, and the shear stress rxy, at the point.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 23.6 ksi, Sy = 2.8 ksi, and Sxy = 7 ksi. Assume β=19∘. Determine the normal stresses σx and σy and the shear stress τxy at the point.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 22.6 ksi, Sy = 2.2 ksi, and Sxy = 3.8 ksi. Assume β=33∘β=33∘. Determine the normal stresses σxσx and σyσy and the shear stress τxyτx⁢y at the point.
At a point in a stressed material, the major principal stress is 180 kPa compression and the minor principal stress is 40 kPa tension. (a) Determine the Mohr’s circle for this stress combination. (b) What is the maximum shear stress that acts at the point, and what is the value for the normal stress acting on the plane of maximum shear? (c) Determine the value of the normal and shear stress acting on the plane 22.5° ccw from the major principal plane.
A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure. a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN?c. What is the maximum shear stress in MPa?
5 decimal places 1. At the proportional limit, a certain material has a stress of 78 MPa as the strain is 0.0004. What is the modulus of elasticity of the material in GPa? 2. A 7-ft diameter spherical tank is subjected to an internal pressure of 24 psf. If the wall thickness is 0.35", determine the tangential stress of the wall in psi. A spherical pressure vessel of 5.7 meter diameter is subjected to an internal pressure of 5.0 MPa. Determine the tangential stress (MPa) developed in the wall of the vessel if the thickness is 4 mm.
The major and minor principal stresses acting at a point in a stressed material are 80 psi compression and 20 psi tension. (a) Draw the Mohr’s circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on the plane? (c) Determine the value of the shear and normal stresses acting on a plane that is 30° ccw from the major principal plane.
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 MPa, Sy = 29 MPa, and Sxy = 26 MPa. Assume β=tan^−1(b/a)=23.2∘, a = 7, and b = 3. Using the equilibrium equation approach, determine the normal and shear stresses σ (positive if tensile, negative if compressive) and ττ (magnitude only) at this point on the inclined plane shown.
Q) If the failure of shearing stress in a steel plate is 2,300KN, determine (a) the force required to punch a 32 mm diameter hole in a 10mm thick plate and, (b) the corresponding normal stress ina punch.
The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are Sx = 170 MPa, Sy = 85 MPa, and Sxy = 45 MPa, acting in the directions indicated in the figure. Determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 48°.
At a point on the free surface of a stressed body, a normal stress magnitude of Sy = 54 MPa (C) and an unknown positive shear stress exist on a horizontal plane. One principal stress at the point is 6 MPa (C). The absolute maximum shear stress at the point has a magnitude of 68 MPa. Determine the unknown stresses on the horizontal and vertical planes and the unknown principal stress at the point.