800 lbs 500 lbs 8 ft 5. B 3 8 ft A E 6 ft For the simple plane (2D) truss shown in the figure, determine: 1. The support reactions at points (joints) A (roller support) and E (hinge support). FBD required. 2. The force in each of the seven truss members, and whether the member is in tension (T) or compression (C) For Part 2, you must present your solution in the form of a table shown below. You may not change

800 lbs 500 lbs 8 ft 5. B 3 8 ft A E 6 ft For the simple plane (2D) truss shown in the figure, determine: 1. The support reactions at points (joints) A (roller support) and E (hinge support). FBD required. 2. The force in each of the seven truss members, and whether the member is in tension (T) or compression (C) For Part 2, you must present your solution in the form of a table shown below. You may not change

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.23P: The truss ABC shown in the figure supports a vertical load W at joint B. Each member is a slender...

See similar textbooks

Similar questions

A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
A truss ABC supports a load W at joint B, as shown in the figure. The length L, of member Aß is fixed, but the length of strut BC varies as the angle is changed. Strut BC has a solid circular cross section. Joint B is restrained against displacement perpendicular to the plane of the truss. Assuming that collapse occurs by Etiler buckling of the strut determine the angle for minimum weight of the strut.
A soccer goal is subjected to gravity loads (in the - z direction, w = 73 N/m for DG, BG, and BC; w = 29 N/m for all other members; see figure) and a force F = 200 N applied eccentrically at the mid-height of member DG. Find reactions at sup ports C, D, and H.
The truss ABC shown in the figure supports a vertical load W at joint B. Each member is a slender circular steel pipe (E = 30,000 ksi) with an outside diameter of 4 in. and wall thickness 0.25 in. The distance between supports is 23 ft. Joint B is restrained against displacement perpendicular to the plane of the truss. Determine the critical value Wcr of the load.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A steel post (E=30×106) having thickness t = 1/8 in. and height L = 72 in. support a stop sign (see figure), where s = 12.5 in. The height of the post L is measured from the base to the centroid of the sign. The stop sign is subjected to wind pressure p = 20 lb/ft2 normal to its surface. Assume that the post is fixed at its base. What is the resultant load on the sign? (Sec Appendix E, Case 25, for properties of an octagon, n =8.) What is the maximum bending stress in the post? Repeat part (b) if the circular cut-outs arc eliminated over the height of the post.
For the truss given below, it is desired to determine the normal efforts that act on the members, so that, thus, possible constraints for its design are possible. Consider that at point A there is a second gender support; and at point D, a first-class support. As this is asked: what is the effort acting on bar AB? Is it guidance or assessment?Source: Hibbeler (2004, p. 588). HIBBELER, R. C. Resistance of Materials. 5. ed. Rio de Janeiro: Technical and Scientific Books Publisher, 2004. Question 1 options: a) A compression force of 100 kN acts on bar AB. B) A tensile effort of 100 kN acts on bar AB. c) A compressive force of 141.42 kN acts on bar AB. d) A compression force of 200 kN acts on bar AB. e) A tensile effort of 141.42 kN acts on bar AB.
Consider the truss shown in the figure, built from three struts attached by three pins. The truss supports a downward force of F = 1,250 N applied at the point B. Assume the mass of the truss is negligible, the pins are frictionless, and the supports at A and C are also frictionless. (a) Assuming ?1 = 25.0° and ?2 = 49.0°, what are nA and nC? (Enter the magnitudes in N.) nA= NnC= N (b) The force any strut applies on a pin must be directed along the length of the strut as a force of tension or compression. What are the directions of the forces that the struts exert on the pins joining them? strut AB on joint A: strut AB on joint B: strut BC on joint B: strut BC on joint C: strut AC on joint A: strut AC on joint C: Find the force of tension or of compression (in N) in each of the three struts. bar AB Nbar BC Nbar AC N
in the fink truss shown in fig. p-4-4.5, the web members BC and EF are perpendicular to the inclined members of their midpoints. if p=2000lb, use the method of sections to determine the force in DF, DE, and CE
Two gondolas on a ski lift are locked in the postion show in the figure while repairs are being made elsewhere.The distance between support towers is L = LOO ft.The length of each cable segement under gondolas weighing WB= 450 lb and Wc=650 lb are DAB=12 ft, DBC=70 a , and DCB=20 ft . The cable sag at B is AB = 3.9 ft and that C is A = 7.1 ft.THe effective cross-sectional area of the cables is Ae=0.12 in". (a) Find the tension force in each segment; neglect the mass of the cable. (b) Find the average stress(σ) in each cable segment.
using the method of sections , analyse the truss shown in figure 8 below reguarding forces in menbers ED , DF AND FC .
The planar truss shown in the figure below (fig.2) is a structure composed of slender members (metal bars) joined at their endpoints. You are asked to:(a) Determine the support reactions observed by the plan truss; joint pin at A, and roller support at F. (b) Using the joints method determine the force in members “DE”, “DF”, and “DC”. State if these members are in tension [T] or compression [C](c) Determine all the zero-force members.