I need the answer as soon as possible 9. A water pump has one inlet andas shown infigure , all at the same elevation.shaftP 500 kPaD=6 cmtwooutletstheP = 120 kPaV = 5 m/sD = 12 cmP = 300 kPaV 20 m/sD = 4 cmWhatpumppowerisrequired if the pump efficiencyis ( 85 % ) ? Neglect all losses.Consider steady inconnpressible flow of wator through the device shown in the

Answered: Image /qna-images/answer/fd6b2976-78c2-43e1-a6ab-66453491b68b.jpg

9. A water pump has one inlet and two outlets P = 500 kPa as shown in the D=6 cm figure , all at the same elevation. shaft P 120 kPa, V = 5 m/s D = 12 cm P = 300 kPa V 20 m/s D= 4 cm What is power required if the pump efficiency is ( 85 % ) ? Neglect all losses. pump

9. A water pump has one inlet and two outlets P = 500 kPa as shown in the D=6 cm figure , all at the same elevation. shaft P 120 kPa, V = 5 m/s D = 12 cm P = 300 kPa V 20 m/s D= 4 cm What is power required if the pump efficiency is ( 85 % ) ? Neglect all losses. pump

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 3. A 90% efficient Francis turbine running at 100 rpm discharges 6m * 3/s of water. The inner runner…

Q: A pump has the following parameters N= 2133.5 RPM, Ns = 40 RPM, D = 37.1 cm and is used to pump…

A: As per the guidelines, I can solve only 1st three sub-parts. For rest parts, please re-post again.…

Q: At a hydraulic plant, the difference in elevation between the surface of the water at intake and at…

Q: A positive displacement pump has a capacity of 8 cm3 per revolution and runs at 1000 rpm. Its…

A: Given: N - 1000 rpm v - 8 cm3/rev nv - 0.89 K - 2.4 x 104 bar p - 1 bar/s V - 500 L To find :…

Q: Q2/ A pump delivers water from a tank A (water surface elevation = 110 m) to tank B (water surface…

A: Data given-

Q: The suction diameter of 60mm reads 2psi vaccum and 50mm diameter discharge with 250kpag. The suction…

Q: 3.5 A pipe 50 cm in diameter carries water (10°C) at a rate of 0.5 m/s. A pump in the pipe is used…

A: Answer: The power that must be supplied to the pump is 203.7650 kW (273.1434 hp).

Q: Problem 2. At a hydroelectric power plant the flow is 3.25 meter cubed per second, the friction loss…

A: Given, Inlet flow = Qin = 3.25 m3/sFricition head loss in penstock = Hf = 15 mAvailable head = H =…

Q: The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated…

A: Given: Q=200 lpsPB=690 kN/m2PA=206 kN/m2zA=67 mzB=30 mdA=300 mm = 0.3mdB=200 mm =0.2 m

Q: If the diameter and length for pipel is (900mm, 1500m); pipe2 is (600mm, 900m) and pipe3 is (500mm,…

Q: A hydroelectric power plant is being designed. The gross head from the reservoir to the tailrace is…

A: Write the given data

Q: 80°F find

A: The diameter of the penstock is d=80 in. The discharge through the penstock is Q=712 ft3/s.

Q: A centrifugal pump delivers 227 m3/hr of water from a source 4 meters below the pump center line to…

A: Given Data density of water, 1000 Kg/m3 Water head from suction to pump entire line =4 Water head…

Q: the hydraulic motor in the following figure, geometric volume is 10ml/r, working pressure is10MPa,…

A: Theoritical Power = Pressure * Flow rate =1000000 * 10/1000 * 1500/60 = 25 kW With leakage into…

Q: 08. The turbine shown in Figure develops 2500 kW when the water flowrate is 20 m'/s. The head loss…

A: Given: Assume the diameter of the pipe as 2 m.

Q: The penstock of hydroelectric turbine is 0.5m x 0.5m with velocity of 5.5m/s and head of 20m. What…

Q: For the hydraulic motor in the following figure, geometric volume is 10ml/r, working pressure…

A: Disclaimer: Since you have posted a question with multiple sub-part, we will solve the first three…

Q: 4. Hydroelectric power plant has the following data: Type of turbine - - Francis Gross head - - - 75…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The cylinder bore diameter of a single-acting reciprocating pump is 180 mm and its stroke is 360 mm.…

A: Given that, Diameter of bore, d=180 mm,Stroke of pump, L=360 mm,rpm of pump, N=53 rpm,Height of…

Q: Design a most efficient pump size (Find the pump and associated pump curves on the next page) to…

A: To determine the properties of the pump used in the question, we must first calculate the flow rate…

Q: The horizontal pump in Fig.1 discharges water at 57 m3/h. Neglecting Losses,What power in KW is…

Q: Q4: Three pipes (A, B and C), if diameter of A equal to B, diameter of A less than C by 25%,…

Q: Q3) Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter), B DC Horizontal then…

A: Given details; T=10°CLAB=5 mLBC= 3 mdAB=40 mmdBC=30 mmQ=2 L/SecPA=275 kPa

Q: A water circulation system is shown schematically in the figure below. Water enters a pump, followed…

Q: is d, where it is d, for the delivery one. The pump receives a mechanical power P from an electric…

Q: 15. Refer to the figure below. In a hydroelectric power plant, 70m/s of water (p = 1010kg/m) flows…

Q: The tailwater elevation and the headwater elevation of a hydroelectric plant are 80m and 140m…

Q: 4 Three pipes (A, B and C), if diameter of A equal to B, diameter of A less than C by 5%, elevation…

Q: A farmer has a pump which discharges 100 lpm of water at a head of 10 m. The pump is driven by an…

A: Q1= 100lpm H1= 10m N=1700 rpm Pully-drive Combination (4"X4") ⇒D1= 4" D2 = 6 in

Q: 5. Refer to the figure below. In a hydroelectric power plant, 70m/s of water (p = 010kg/m³) flows…

Q: The cylinder bore diameter of a double-acting reciprocating pump is 170 mm and its stroke is 370 mm.…

A: Given: Diameter of the double acting reciprocating pump is 170 mm. Stroke is 370 mm. N = 55 rpm.…

Q: 4.7 Find the power required to pump water from one tank to another, as shown in Fig. 4.31. The…

Q: 2500kW power is generated shown below with a water flowrate of 20 m3/s. The head loss for the entire…

A: Given: Power of the turbine is 2500kW. Flow rate of water is 20 m3/s. Head loss in entire flow is…

Q: Problem 6.7 A pipe of diameter 400 mm carries water at a velocity of 25 m/s. The pressures o points…

A: Solution:

Q: A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe…

A: Friction factor, f=0.015Pipe length, L=2500 ftPipe diameter, d=6 in=612ft=0.5 ftLosses less than…

Q: 08. The turbine shown in Figure develops 2500 kW when the water flowrate is 20 m'/s. The head loss…

A: Power developed by the turbine, P=2500 kWWater flow rate, Q=20 m3/sTotal head loss, hL=2.5 m

Q: 2. In the figure shown, a liquid is pumped from reservoir A to tank B by a 12 hp pump having an…

Q: 04: Three pipes (A, B and C), if diameter of A equal to B, diameter of A less than C by 25%,…

Q: A pipe 50 cm in diameter carries water (l0°C} at a rate of 0.5 m 3 / s. A pump in the pipe is used…

Q: The net head of a little aquarium pump is given by the man- ufacturer as a function of volume flow…

A: From the given data,

Q: In case of Reciprocating pump if we know the actual discharge is 1.0796 x 10°m'/sec, time taken to…

A: Given data Actual discharge (Q) = 1.0796 x 10-3 m3/s Time (t) = 44 sec Head (h) = 19 cm = 0.19 m

Q: The cylinder bore diameter of a single-acting reciprocating pump is 150 mm and its stroke is 310 mm.…

Q: 1.1. The pump whose performance curves are shown in Figure P1.1 is operated at 1750 rpm and is…

A: for problem 1.1 according to the given diagram: Q = 140 gpmH =50ftη = 50% flow rate = 140 gpm =…

Q: The pump shown in the figure below delivers a head of 300 ft to the water. Determine the power that…

A: Given Data:Head delivered by pump = hp = 300ftDifference in elevation = z2 - z1 = 250ftPipe length =…

Q: It was determined that for a length of 1.6 km of 90 cm diameter pipe made of wood staves the head…

Q: 04: Three pipes (A, B and C), if diameter of A equal to B, diameter of A less than C by 25%,…

Q: It is required to water pump through a pipe(P.V.C) of diameter = 2 inches and 100 m, head to a…

A: Pump It is a device which lifts the water or any liquid from lower elevation to higher elevation.…

Q: A water pump has one inlet and outlets as shown in the P 500 kPa D= 6 cm two figure , all at the…

Question

I need the answer as soon as possible

9. A water pump has one inlet and
as shown in
figure , all at the same elevation.
shaft
P 500 kPa
D=6 cm
two
outlets
the
P = 120 kPa
V = 5 m/s
D = 12 cm
P = 300 kPa
V 20 m/s
D = 4 cm
What
pump
power
is
required if the pump efficiency
is ( 85 % ) ? Neglect all losses.
Consider steady inconnpressible flow of wator through the device shown in the

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Step 3 Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pump increases the pressure of water from 100 kPa to 900 kPa to an elevation of 35 m. The inlet and outlet diameters are identical. The net head of the pump is (a) 143 m (b) 117 m (c) 91 m (d) 70 m (e) 35 m
The penstock of hydroelectric turbine is 0.5m x 0.5m with velocity of 5.5m/s and head of 20m. What is the output of the turbine if the turbine efficiency is 92%?
choose the correct answer Q1A- Using water jet forces to operate turbines in hydropower plant consider application of: * a) Bernoulli’s equation b) Darcy-Weisbach Equation c) Manning equation d) Momentum equation E-none of all above B-The main difference between the flow in pipes and the flow in open channels is * a) Existing the head loss b) Existing the free surface c) Existing the pressure drop d) None of all above
A hydroelectric power plant is being designed. The gross head from the reservoir to the tailrace is 1065 ft, and the volume flow rate of water through each turbine is 203,000 gpm at 70°F. There are 12 identical parallel turbines, each with an efficiency of 95.2 percent, and all other mechanical energy losses (through the penstock, etc.) are estimated to reduce the output by 3.5 percent. The generator itself has an efficiency of 94.5 percent. Estimate the electric power production from the plant in MW
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
A pump was installed with a suction head of 6 meter and a discharge head of 10 meters. The discharge rate of the pump is 60 liters per minute. What is the water horsepower of the pump?
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m.The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? **provide complete solution using bernoullis equation..provide illustration with labels like datum line and such** Show all formula derivation
Estimate the power available from a proposed micro hydro scheme at a site having a small stream of 100 l/s of flow at a head of 30 m. Assume the overall efficiency of the system is 60% and density of fresh water is 994 kg/m^3.
At a hydroelectric plant the difference in elevation between the surfaace of the water at the intake and at the tailrace is 183m (600ft). When the flow is 80 cfs, the friction loss in the penstock is 60 ft and the head utilized by the turbine is 460 ft. The mechanical friction in the turbine is 100hp, and the leakage loss is 3 cfs. Find (a) hydraulic efficiency; (b) volumetric efficiency; (c) power delivered to shaft; (d) brake horse power, (e) mechanical efficiency; (f) over-all efficiency.
A certain hydropower plant is being supplied by river flow of 900 cubic ft/sec and the head on the site is 200 ft. To develop maximum capacity it was proposed to install 2 turbines, one of which is 1.5 times the capacity of the other. Both turbine units are assumed to have efficiency of 85%. Determine (a) the total power developed, (b) what is the power developed by turbine #1 and by turbine #2 and (c) Rotative speed of each turbine unit assuming specific speed equal to 70 rpm.
A Kaplan turbine working under a head of 43 m deve-lops 15,400 B.H.P. The dia of theboss is 0"3 times the dia ofrunner. Determine the speed and dia of runner, if speed ratio is2, flow ratio as 0-65 and overall efficiency as 91%.
A multi stage pump is required to deliver of 2 l/s water against a maximum discharge head of 240 m. The diameter of radial bladed impeller should not be more than 15 cm. Assume a speed of 2800 rpm. Determine the impeller diameter, and power. Overall efficiency is 0.7.