is d, where it is d, for the delivery one. The pump receives a mechanical power P from an electric motor. What is the maximum height h, above the water level to which water can be pumped? A loss head H, due to friction is considered. dd P Water reservoir Q = 280 N.s-1 d, = 165 mm da = 135 mm P =98 kW HL =12 m

is d, where it is d, for the delivery one. The pump receives a mechanical power P from an electric motor. What is the maximum height h, above the water level to which water can be pumped? A loss head H, due to friction is considered. dd P Water reservoir Q = 280 N.s-1 d, = 165 mm da = 135 mm P =98 kW HL =12 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a pump operating at 1750 rpm delivering 600 gpm against total head of 200 tt. changes in the piping system have increase the total head of 450 tt. At what RPM should the pump be operated to achieve thus new head at the same efficiency?
PROBLEM 02: Water entering a pump through an 200mm diameter pipe at 27.6 kPa has a flow rate of 0.1 m^3/s. It leaves the pump through a 100mm diameter pipe at 103.4 kPa. Assuming that the suction and discharge sides of the pump are at the same elevation, find the horsepower delivered to the water by the pump (746 watts = 1 HP). Illustrate the problem and show your complete solution.
A centrifugal pump with 2.3 diameter impeller running at 327 rpm delivers 7.9 m3/s of water. The head developed is 72.8 m. The width of the impeller at outlet is 0.22 m. If the overall efficiency is 91.7% determine the power to drive the pump.
A submersible pump of 80 percent efficiency is used in pumping water with flow rate,Q from a river to a pool at an elevation, h. The frictional losses is assumed with losscoefficient, K = 10. By the aid of a labelled diagram, derive an expression on thepower require to drive the pump.
Q6: Calculate the specific speed for the centrifugal pump operates at (3000 r.p.m) & head of (6m) and discharge of (0.2 m3/s).
A multi stage pump is required to deliver of 2 l/s water against a maximum discharge head of 240 m. The diameter of radial bladed impeller should not be more than 15 cm. Assume a speed of 2800 rpm. Determine the impeller diameter, and power. Overall efficiency is 0.7.
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
An existing pump is used to pump water with the following data at BEP: D = 2.15 in, N = 1784 rpm, ρ = 998 kg/m3, Q = 18 gpm, H = 4.2 ft. A larger pump is to be designed based from the existing one to be used for pumping slurry (ρ = 1220 kg/m3) such that its best efficiency point occurs as close as possible to a volume flow rate of 48 gpm and at a net head of 15 ft. Calculate the new pump diameter in inches. Round off your final answer to 3 decimal places.
The suction water level of a reservoir is 5 m above pump centerline and the discharge water level is 50 m above pump centerline. The discharge is 0.2 m^3/s with suction pipe of 100 mm diameter and 90 mm diameter discharge pipe. The total head loss is 50% of the velocity head at suction pipe. If pump runs at 360 rpm, find the torque (in kN-m) developed by the shaft of the motor if pump efficiency is 76%.
A radial flow pump operating at maximum efficiency at a specific speed of 2300 is to deliver 260gpm against a head of 129ft at a rotative speed of 2100 rpm. Find the required number of stages. ANSWER: 3
It is desired to construct a hydraulic turbine for a hydraulic power plant to operate under the following conditions: discharge Q = 3.5 m3/s of water, the available net head = 290 meters, the hydraulic efficiency = 0.8, the rotating speed = 300 rpm. A Pelton wheel impulse turbine was selected with the following specifications: the bucket angle b2 = 160°, the coefficient of velocity for the nozzle is 0.98 and assume the friction coefficient k = 0.2. Determine the following:Jet Diameter to Wheel diameter ratio, dj/Dw. The Specific Speed in M.K.S., Ns.The computed head coefficient ϕ.The brake horsepower. The required number of Jets. The Pelton wheel diameter in meters.
The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21 x10-5 m² from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height of the the water level in the tank in order to maintain 5.0 Psig pressure at point A