Answered: 9. Determine the height that 20°C water…

9. Determine the height that 20°C water would climb in a vertical 0.02 cm-diameter tube if it attaches to the wall with an angle ß of 30° to the vertical

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Related questions

Q: A) A thin 4-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless…

Q: Question 1. The homogeneous gate shown in Figure consists of one quarter of a circular cylinder and…

Q: A hemispherical cistern of 4 m radius is full of water. It is fitted with 60 mm diameter sharp-edged…

Q: Determine the surface tension of liquid in contact with air and a glass tube. If the capillary tube…

Q: Determine pressure at depth of 12.33 m from free surface of water

A: Given data, h= 12.33 m Need to find pressure at depth of water

Q: The curved surface given in the figure is defined by y = 3√x. Determine the horizontal force and its…

A: Understand that the horizontal force of the curved surface is obtained using the projected area of…

Q: Find the resultant force which acts on the gate's submerged face if the gate is 4 m long. 5m 5m 60°…

Q: A 5.75-mm ID capillary tube is coated with waxy material causing it to have a wetting contact angle…

Q: Problem 2 Hinge A stop-block on the edge of the gate at B will break whenever the force reaches…

A: Given DataP=40kNL=1mB=1.5mθ=90°

Q: Q1) Water flowing through a jet with velocity of 30 m /s. Caleulate the value of (0) to be the water…

Q: Evaluate the total force on the gate (unit width) and its direction. (specific weights of Water:…

Q: Q: Water has a surface tension of (0.4 N/m). In a (3mm) diameter vertical tube if the liquid rise (6…

Q: 8. A siphon draws oil (sg=0.86) as shown in the figure. Determine the pressure at point "A", kPa. *…

A: We have given

Q: A 5.75-mm ID capillary tube is coated with waxy material causing it to have a wetting contact angle…

A: Given Diameter, d = 5.75 mm Angle = 54.5o Take Density = 1000…

Q: T= 20°C Consider the water reservoir with a siphon as shown in the figure. If d = 0.06 m, D = 0.25…

Q: 1- The flow of water from a reservoir is controlled by a5-ft-wide L-shaped gate hinged at point A,…

Q: A 2.5 - M CABLE HAVING A TENSILE STRENGTH OF 1256 N IS USED TO KEEP THE GATE SHUT. HOWEVER, AT A…

A: Given data Tension on the cable = 1256 NLength of cable = 2.5 mHeight at which it is hoisted = 2.1…

Q: An open rectangular vessel shown is filled with water. Determine the volume of spillage if it is…

A: Given Acceleration, a = 1.8 m/s2 Length, l = 3 m Width, w = 1.2 m…

Q: The drinking water needs of an office are met bylarge water bottles. One end of a 0.35-in-diameter,…

A: Given data, Assumption: - Steady Flow, Incompressible & Irrotational flow, Neglect all minor…

Q: Water flows steadily through the elbow, placed horizontally on the surface shown in figure.…

Q: A hemispherical tank of 4 m radius is full of water/ It is fitted with a 60 mm diameter sharp-edged…

Q: Determine the value of h in the siphon shown if velocity at C was 11.7 m/s. Diameter of the pipe is…

A: Given:- Diameter of pipe (d) = 2.5 cm Velocity at point (c) = 11.7 m/s To Determine :- Height (h)…

Q: A water tank is filled with water to a height of 4.3m above the 10mm diameter orifice which is…

A: Draw the diagram for the given question.

Q: A 300 mm diameter steel pipe 12-mm thick carries water under a head of 50 m of water. Determine the…

Q: water, while the other arm contains both f to-water height ratio of 4. Determine the heig n that…

Q: Determine the surface tension (N/m) in a tube with 0.2m radius and wetting angle 0° and capillary…

A: The solution of given problem is provided by considering the capillary rise in 'm' and 'mm', because…

Q: height of the water h which will first cause the gate to open.

A: Given: To determine height h

Q: 8. A 3-m-wide, 8-m-high rectangular gate is located at the end of a rectangular passage that is…

Q: Water flows steadily through the elbow, placed horizontally on the surface shown in figure.…

Q: Determine the value of H if the pressure difference PA-PB = 100 kPa

A: PA-PB=100 kPa=100*103 Pa SGo=0.827

Q: Question 2 The curved surface given in the figure is defined by y = 3vx. Determine the horizontal…

A: Question 2: Given: The equation of curved line, y=3x1/2 The width of gate, b = 2 m

Q: An open vessel in the form of a frustum of a cone with a radius of 1.2m (bigger base) on top, the…

Q: Determine the minimum size of glass tubing that can be used to measure water level, if the capillary…

A: Given Capillary rise, h = 0.25 mm Surface tension = 0.0735 N/m Find Size of the glass tube, d

Q: A 5.75-mm ID capillary tube is coated with waxy material causing it to have a wetting contact angle…

Q: 7- Referring to Fig., determine the horizontal and vertical forces due to the water acting on the…

A: From the given data;

Q: A5.75-mm ID capillary tube is coated with waxy material causing it to have a wetting contact angle…

A: Given Diameter, d = 5.75 mm Angle = 54.5o Take Density = 1000 kg/m3 Surface tension =…

Q: If the wall AB shown is 48 meter long calculate the total force (In the uhit of KN) on the wall due…

Q: In the figure shown, what the minimum height (h) t which water must rise in th water tank in order…

Q: Water flows steadily through the elbow, placed horizontally on the surface shown in figure.…

Q: A circular tank of diameter 3 m contains water up to a height of 4 m. The tank is provided with an…

Q: 1.2 m and diameter 0.6 m is three quarters filled with water when stationary. If the tank is rotated…

Q: An N-shaped glass tube with its right vertical leg open at the top is partly filled with water as…

A: When an object or a body is immersed in a liquid, it experiences pressure that is exerted by the…

Q: Water shoots out from a large tank consisted of two layers of liquid as shown in If 3.2 m of water…

A: Given data: The amount of water is 3.2 m3 The diameter of the column is d=0.3 m

Q: 3. An open cylindrical vessel 1.2 m in diameter and 2.1 m high is 2/3 full of water. Compute the…

A: Answer: The amount of water spilled out off the tank is 130 litres.

Q: Q: Find the time required to empty a tank with water height (h=18) 8 ft A 20 ft circular hole

A: Given: Height of the tank (H)=20ftHeight of water (h)=18ftRadius of the tank (R)=8ft

Q: tethe magnitude and direction ot the force exerted by the water on the curved BCof the conduit. The…

A: The hydrostatic force on the curved surface on in different orientations so the resultant force can…

Q: Determine the weight per meter of length of the semi-circular gate shown below that would maintain…

Q: An open cylindrical vessel with a diameter of 1m contains water at a depth of 3.56m. If it is…

Question

9. Determine the height that 20°C water would climb in a vertical 0.02 cm-diameter tube
if it attaches to the wall with an angle B of 30° to the vertical.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

If the rate of rotational speed of the 3-tube system shown is ? = 10 rad/s, determine the water heights in each tube leg. At what rotational speed will the middle tube be completely empty?
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
The three reservoirs system contains water. If L1 = 2000 m, f 1= 0.013, D1 = 1m; L2 = 2300 m, f2 = 0.02, D2 = 0.60m; and L3 = 2500 m, f = 0.023, D3 = 1.20m. Compute Q3 in m3/s.
Find the surface tension of the water droplet of 30 mm diameter when the inside pressure is 3.5 N/m2 The surface tension in N/m is
Answer is: V = 14.17 ft/s
Calculate the change in water pressure from the surface to a depth of 5m. Is this just (9.81m/s^2)(5m)?
If the pressure in a tank of oil (sp gr 0.85) is 375kn/m2, what is the equivalent head; (a) in meters of the oil; (b) in meters of water; (c) in meters of mercury? NOTE: Clear handwritten solution
The two sides of a V-shaped water trough are hinged to each other at the bottom where they meet, as shown, making an angle of 45° with the ground from both sides. Each side is 0.75 m wide, and the two parts are held together by a cable and turnbuckle placed every 6 m along the length of the trough. Calculate the tension in each cable when the trough is filled to the rim.
15- What will be the diameter (in mm) of a water droplet, the pressure inside which is 0.00221 N/cm2 greater than the outside pressure? (Take surface tension as 0.075 N/m)
A hemispherical tank of 4 m radius is full of water/ It is fitted with a 60 mm diameter sharp-edged orifice at the bottom. Calculate the time required to lower the level in the cistern by 2 m. Take Cd= 0.6
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.