92 2. A long pin is used to hold the piston in place as shown in the diagram. The hw bbnilve cylinder is then placed into boiling water. vis a. Does the temperature of the gas increase, decrease, or remain the same? Explain. Ideal gas noig i b bad bensa elndi reled boemnib viod-nt ow banage et ov b. Sketch this process in the PV diagram at right. c. Explain why for this particular situation, it is not possible to determine the pressure of the gas as you did on page 1 of the tutorial (i.e., by considering a free-body diagram of the piston). Taitini odl oi с. 1o o285.fonit orha bawalla o didw ban t li blod s be 25iliacup o l doirdw 22001g eiti al

92 2. A long pin is used to hold the piston in place as shown in the diagram. The hw bbnilve cylinder is then placed into boiling water. vis a. Does the temperature of the gas increase, decrease, or remain the same? Explain. Ideal gas noig i b bad bensa elndi reled boemnib viod-nt ow banage et ov b. Sketch this process in the PV diagram at right. c. Explain why for this particular situation, it is not possible to determine the pressure of the gas as you did on page 1 of the tutorial (i.e., by considering a free-body diagram of the piston). Taitini odl oi с. 1o o285.fonit orha bawalla o didw ban t li blod s be 25iliacup o l doirdw 22001g eiti al

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter13: State Of Matter

Section13.4: Solids

Problem 42PP

See similar textbooks

Similar questions

A gas with an initial temperature of 900°C undergoes the process as shown.a. What type of process is this?b. What is the final temperature?c. How many moles of gas are there?
How much heat transfer is required to raise the temperature of a 0.750kg aluminum pot containing 2.50 kg of water from 30.0◦ C to the boiling point and then boil away 0.750 kg of water? (2) How long does this take if the rate of heat transfer is 500 W? Draw a diagram and explain your reasoning for each step
A constant-volume gas thermometer hasa pressure of 80.3 kPa at -10.0 °C and a pressure of 86.4 kPa at 10.0 °C. (a) At what temperature does the pressure of this systemextrapolate to zero? (b) What are the pressures of the gas at thefreezing and boiling points of water? (c) In general terms, howwould your answers to parts (a) and (b) change if a different constant-volume gas thermometer is used? Explain.
0.0040 mol of gas undergoes the process as shown.a. What type of process is this?b. What are the initial and final temperatures?
A gas with an initial temperature of 740 °C undergoes the process shown in. (B) What is the final temperature? (C) How many moles of gas are there?
A student is asked to sketch a pV diagram for a gas that goes through a cycle consisting of (a) an isobaric expansion, (b) a constant-volume reduction intemperature, and (c) an isothermal process that returns the gas to its initial state. The student draws the diagram as shown. What, if anything, is wrong with the student’s diagram?
The pV diagram in the figure (Figure 1) shows a process abc involving 0.350 mol of an ideal gas. What was the temperature of this gas at points a, b, and c? How much heat had to be put in during the process to increase the internal energy of the gas by 1.30×104 J ?
Pressure cookers increase cooking speed by raising the boiling temperature of water above its value at atmospheric pressure. (a) What pressure, in pascals, is necessary to raise the boiling point to 125°C? You can use the table above and assume that the vapor pressure depends linearly on the temperature between the existing data points. (b) What gauge pressure, in atmospheres, does this correspond to?
A student is asked to sketch a pV diagram for a gas that goes through a cycle consisting of (a) an isobaric expansion, (b) a constant-volume reduction in temperature, and (c) an isothermal process that returns the gas to its initial state. The student draws the diagram shown in the figure. What, if anything, is wrong with the student's diagram?
No need for explanation just find A) what volume must the gas be compressed to increase its pressure to 150kpa B) at what volume will the gas have 280K? I’ll rate, please ASAP.
You do an experiment in which you transfer energy to 1.2 moles of a gas and measure it’s change in temperature. You make a graph of the data as shown. The y-axis is the amount of energy added and the x-axis is the temperature. A) how many moles per molecule does this substance have? B) is the substance most likely a monatomic gas, diatomic or another type of gas?
N2 gas in a container is contracted by one third of the original volume to a total of 12 dm3 isothermally. The pressure is now 2 bar, what was the original pressure before the contraction?